Nikon AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED Скачать руководство пользователя страница 33

Страница: 33 / 98

JAA79651-R.3695.A

- Ａ・AF-S DX 8-35/3.5-5.6G -

・

Fit the convex portion of the segment gear ring in the concave portion of the SWM base unit, and assemble

them. Then rotate the segment gear ring in the direction of the arrow.

Segment gear ring

Grease: I-40

Magnetic tape surface

Caution: Do not touch the magnetic surface directly with hand/tool.

Convex

portion

Concave portion

Apply to the sliding surface with
the segment gear ring.

Apply to SWM base unit and
sliding surfaces

SWM base unit

Torque rubber

Adhesive: C-8008B

Grease: GP-1RS

Apply to over all groove ×3.

Segment gear ring

Содержание AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED



































































































Результаты поиска

Содержание AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Отзывы:

Похожие инструкции для AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Бренды по названию

Популярные бренды

Nikon AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED, Руководство по ремонту

Результаты поиска

Содержание AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Отзывы:

Похожие инструкции для AF-S DX Zoom Nikkor 18-135/3.5-5.6G ED

Бренды по названию

Популярные бренды