Nidac Presco 3 Series Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 24

Nidac Presco 3 Series Скачать руководство пользователя страница 9

6

One Minute Lockout

To increase security the PAC1 can be set to lock out all
codes for a period of 1 minute after 5 incorrect codes have
been tried (set in memory 87, refer to page 16).

Note

that

this feature should not be enabled if access must be
guaranteed in an emergency situation.

High Security Mode

The PAC1 can be set up to operate in one of the four
modes described below.

Normal Mode (High Security Mode Disable)
Any one of the programmed user codes will operate the
ELC relay.

Any Two User Codes
Any two of the programmed user codes must be used
together to operate the ELC relay.

Code 000 or 001 and any other user code
The user code stored in memory 000 or 001 used
together with any other valid user code will operate the
ELC relay.

Sequential Memory User Codes
Two user codes in sequential memory locations must be
used together to operate the ELC relay. The paired
code locations start with an even number, e.g. 000 &
001, 056 & 057, 138 & 139, etc.

IMPORTANT NOTE:

When the PAC1 is set up to use any

of the high security modes above, the ELC relay will only
operate in

Momentary (timed) Mode

even if the codes are

programmed as Toggle codes.

«
...
7
8
9
10
11
...
»

Содержание Presco 3 Series

























Отзывы:

Нет отзывов