Nicherons FXO Скачать руководство пользователя страница 34

Страница: 34 / 53

SpoTel Series Voice Gateway:-‐ User Manual

Renew DHCP

*193#, set dynamic IP again

Access Web by Wan in Rout Mode

Allow access web through WAN port

：

*160*1#; don’t allow access

web through WAN port

：

*160*0#

Reset Factory

*166*000000#, reset factory

Restart Device

*111#, restart device

Call onhold/offhold

When call process, dial*# into call hold.

（

Recovery the call through

hook flash or *#

）

Call by IP

Directly dial the end user IP to call

Call Waiting Activate

*51#, enable call waiting function

Call Waiting Deactivate

*50#, forbid call waiting function

Blind Transfer

If the call transfer to 801, first hook flash and then dial the *
87 * 801#

Call Forward Unconditional Activate

*72*+ phone number#, transfer the call from the phone number

Call

Forward

Unconditional

Deactivate

*73#, forbid call forward unconditional

Call Forward Busy Activate

*90*+ forward busy number#

Call Forward Busy Deactivate

*91#, forbid call forward busy

Call Forward No Reply Activate

*92*+ forward no reply number#

Call Forward No Reply Deactivate

*93#, close this function

Do Not Disturb Activate

*78#, enable DND function

Do Not Disturb Deactivate

*79#, close DND function

Dial Voicemail

*200#, visit voice mail box

Note

：

* Private services are open by default

4.8.7 System Parameter

System parameters include: STUN

、

NTP

、

Provision

、

WEB parameter

、

Telnet.

）

STUN

(

Session Traversal Utilities for NAT

) is a standardized set of methods and a

network protocol to allow an end host to discover its public IP address if it is located behind a

NAT. The STUN protocol allows applications operating behind a network address translator

(NAT) to discover the presence of the network address translator and to obtain the mapped

(public) ip address (NAT address) and port number that the NAT has allocated for the

application's UDP connections to remote hosts.

Содержание FXO






















































Результаты поиска

Содержание FXO

Отзывы:

Nicherons FXO, Руководство пользователя, Страница: 34 / 53

Результаты поиска

Содержание FXO

Отзывы: