Nice Apollo 816 LA Скачать руководство пользователя

Страница: 22 / 26

Apollo 816 LA Linear Actuator

Installation Reference Manual

HINTS

• C

heck limit position is set correctly by using the arrow buttons to jog the gate to mid-position and

then to the limit.

For Limit LED behavior, see

DETAIL A in Diagram 6-1 and Fig-11B below (and

note).

•

Mercury 310 controller will chirp twice when Limit LEDs turn ON, and once when Limit LEDs turn off.

11B

816 LIMITS: MERCURY 310

6.2 816 LIMITS: MERCURY 310

Fig-11B: Mercury 310 Limit LEDs

NOTES

When the actuator reaches either limit during

this procedure,

both

Limit LEDs (Open

and

Close) light up for that actuator (Motor 1 or 2).

IMPORTANT!

These instructions are ONLY for adjusting the location of limit sensors inside the Apollo

816 actuator. After setting these limits, see the “Learn Limits” procedure in the appropriate

controller manual for instructions on how to enable the controller to “learn” these limits.

Remove plastic caps from the Extend and Retract limit screws on the Apollo 816 actuator motor (Fig-11).

2. P

lace Mercury Function Knob to

LRN MOTOR 1

LRN MOTOR 2

(

shows in controller display).

Press/hold Left/Right arrow button to run gate to mid-position.

Press/hold Left/Right arrow button to run gate to a desired gate limit position.

5. If gate does not stop at desired limit position, adjust per one of the following two scenarios (

If gate moves to preferred gate limit position

without stopping

(with NO limit LED indication), use

buttons to move gate to preferred limit position, note if actuator arm is extended or retracted, then

adjust limit screw per

Scenario A

Diagram 6-1

If gate stops

before

preferred gate limit position (with limit LED indication), press gate button again to

to move gate to desired limit position, note if actuator arm is extended or retracted, then adjust limit

screw per

Scenario B

Diagram 6-1

6. To set the other limit, run gate to mid position, then to the

other

limit and repeat from Step 5.

7. After limits are set, replace black plastic caps over 816 actuator Extend and Retract limit screws. If a dual

gate installation, ensure limits are set for each actuator per the above steps.

OPEN

MOTOR 1

Limit LEDs

MOTOR 2

Limit LEDs

www.ApolloGateOpeners.com | (800) 878-7829 | [email protected]

Содержание Apollo 816 LA



























Результаты поиска

Содержание Apollo 816 LA

Отзывы:

Похожие инструкции для Apollo 816 LA

Бренды по названию

Популярные бренды

Nice Apollo 816 LA, Инструкция по установке и справочник

Результаты поиска

Содержание Apollo 816 LA

Отзывы:

Похожие инструкции для Apollo 816 LA

Бренды по названию

Популярные бренды