background image

21

22 - ACCESSORIES AND SENSORS 

EXTERNAL ENTRAPMENT PROTECTION 

Non-contact and contact sensors must be installed individually or in combination with each other to provide external entrapment protection. 

Care should be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate is still moving, and one or more non-

contact sensors shall be located where the risk of entrapment or obstruction exists, such as the perimeter reachable by a moving gate or barrier. 

A hardwired contact sensor shall be located and its wiring arranged so that the communication between the sensor and the gate operator is not subjected to 

mechanical damage. 

A wireless contact sensor such as one that transmits radio frequency (RF) signals to the gate operator for entrapment protection functions shall be located 

where the transmission of the signals are not obstructed or impeded by building structures, natural landscaping or similar obstruction. 

DURING INSTALLATION 

•  DISCONNECT POWER at the control panel before making any electric service power connection. 
•  Be aware of all moving parts and avoid close proximity to any pinch points. 
•  Know how to operate the manual release. 
•  Adjust the unit to use the minimum force required to operate the gate smoothly even during mid-travel reversing. 
•  Place controls a minimum of 8 feet away from the gate so that the user can see the gate and operate controls but cannot touch the gate or gate operator 

while operating the controls. 

•  Warning signs must be placed on each side of the gate or in high-visibility areas to alert of automatic gate operations.

Moving Gate can cause

Serious Injury or Death. 

Persons are to keep clear! The gate is able to be moved without prior warning.
Do not allow children to operate gate or play in gate area.
This entrance is for vehicles only. Pedestrians must use separate entrance.

Le portail en mouvement peut causer 

des blessures graves ou la mort. 

Les personnes ne devront pas s’approcher! 
Le portail est capable d'être bougé sans avertissement préalable.
Ne pas laisser les enfants utiliser le portail ou jouer dans le domaine du portail.
Cette entrée est réservée aux véhicules. 
Les piétons devront utiliser une entrée séparée.

Содержание 73001K

































Отзывы: