Nibe handol 24 Скачать руководство пользователя | Manualshive

Страница: 12 / 15

background image

52

Cut away the punched metal cover in the rear panel
and hang the rear panel over the connecting flue pipe.
Connect the two ends of the flue pipes with an elbow
joint and seal the connection with heat-resistant sealant.

Fit the chimney mantle by lowering it onto the locating pins on the sealing plate. Then fix the rear panel to the mantle. Finally,
lay the covering plate on top.

Pannkitt

Pannkitt

Important!

The installation must be approved by a qualified inspector before the stove is made ready for use.

Read through the lighting and operating instructions for the Handöl 20 series carefully before lighting the

stove for the first time.

GB

Heat-resistant sealant

Heat-resistant sealant

«
...
10
11
12
13
14
...
»

Содержание handol 24
















Отзывы:

Нет отзывов

Похожие инструкции для handol 24

Бренд: Valor Fires Страницы: 49

SUMMIT WOOD INSERT DESIGN-A

Бренд: Pacific energy Страницы: 20

Бренд: Pacific energy Страницы: 32

Бренд: Sunjoy Страницы: 5

Бренд: pleasant hearth Страницы: 6

Бренд: Paramount Fitness Страницы: 7

Бренд: Valor Страницы: 12

Бренд: Valor Страницы: 48

Argon Built 3 Sided

Бренд: Stanley Страницы: 26

Бренд: Napoleon Страницы: 20

WESTMOUNT FHTS80048C

Бренд: Canvas Страницы: 35

REGENT FRLC EN Series

Бренд: Flavel Страницы: 31

MSS136144273001

Бренд: Mainstays Страницы: 16

Бренд: Firesense Страницы: 18

Бренд: Qindao Hichanse Group Страницы: 16

Бренд: Napoleon Страницы: 40

Бренд: UKIAH Страницы: 24

Бренд: Capital fireplaces Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды