manualshive.com logo in svg

NIBE-BIAWAR HK 200M, Руководство по установке

Поделиться
Скачать
NIBE-BIAWAR HK 200M Скачать руководство пользователя страница 4

4

HK 200M

1 Important information

Information regarding 
safety

Serial number

Symbols

Marking

HK  200M  features  the  CE  mark  and  fi re  protection 

IP21.

The CE mark confi rms that NIBE-BIAWAR has taken 

care for product conformity with applicable regula-
tions of relevant EU Directives. The CE is required 
for most products sold in the EU, regardless of their 
place of manufacture.

IP21 means that items with the diameter greater or 
equal to 12.5 mm cannot permeate inside causing 
damage, and that the product has been secured 
against vertically falling water drops.

The device can be operated by children aged over 
8 and persons with physical, sensory, or mental dis-

abilities,  and  without  any  experience  or  knowledge 

about its operation, if supervised or trained in safe 
operation, and if they understand the risks related 
to its operation. The device must not serve as a toy 
for children. Activities related to cleaning and basic 
maintenance must not be performed by unsupervised 
children.

Rights to introduce structural changes reserved.

©NIBE-BIAWAR 2016

This manual contains installation and maintenance proce-
dures for specialists.

The serial number is located at the top of HK 200M.

IMPORTANT

This symbol informs about the risk to the device or a 
person

CAUTION

This symbol points to important information to be not-
ed when operating the device.

ADVICE

This symbol shall mean tips to make product operation 
easier.

CAUTION

When  contacting  the  installation  technician,  always 

provide the product serial number (14 digits).

Serial 

number

Waste disposal

Information for particular countries

Disposal of the packaging shall be the 
responsibility of the installation techni-
cian installing the product, or a special 
waste management facility.

Incorrect disposal of the product by the user is sub-
ject to administrative penalties under applicable reg-
ulations.

Installation manual

This installation manual must be submitted to the Cli-
ent.

Do not dispose of decommissioned prod-
ucts  together with regular household 
wastes. Hand them over to a specialist 
facility.

dealing with waste disposal or salesperson offering 
such services.

Chapter 1 | 

Important information

Содержание HK 200M





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды