Nibart 1060 Series Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 44

Nibart 1060 Series Скачать руководство пользователя страница 5

Series 1060

5

This appliance was listed by LABTEST Certification Inc to the following USA and Canadian gas
appliance standards.

- ANSI Z21.88-2009/CSA 2.33-2009 Vented Gas Fireplace Heaters

- CAN/CGA-2.17-M91, Gas-Fired Appliances for Use at High Altitudes

-CSA P.4.1-09 testing method for measuring annual fireplace efficiency.

The listing label is attached to the appliance on the bottom right side of the appliance.

A copy is shown on page

Please contact Archgard Industries Ltd., if you have any questions regarding the certification of
this appliance.

APPLIANCE CERTIFICATION

INSTALLATION CODES

This appliance must be installed by a qualified gas appliance installer. The installation must
conform with the local codes or, in the absence of local codes, with the current National Fuel
Gas Code ANSI Z223.1/ NFPA 54 in the US, or Installation Code CAN/CGA-B149.1 in Canada.
Electrical connections and grounding must conform with local code, or current National
Electrical code ANSI/NFPA No. 70-1987 in the US, and in Canada the current Canadian
Electrical Code CSA C22.1.
A manufactured home (USA only) or mobile home OEM installation must conform with the
Manufactured Home Construction and Safety Standard, Title 24CFR, Part 3280, or, when such
a standard is not applicable, the Standard for manufactured Home Installations, ANSI/NCSBCS
A225.1 or Standard for Gas Equipped Recreational vehicles and Mobile Housing, CSA Z240.4

We recommend that our gas hearth products be installed and serviced by professionals
who are certified in the U.S. by the National Fireplace Institute

®

(NFI) as NFI Gas

Specialists.

SPECIFICATIONS

/.

Natural Gas (NG)

Propane (LP)

Manifold Pressure

3.5 in. W.C. (0.9 kPa)

10.0 in. W.C. (2.5 kPa)

Min. Supply Press
Max Supply Press

4.5 in. W.C. (1.2 kPa)

14.0 in. W.C. (3.5 kPa)

11.0 in. W.C. (2.8 kPa)
14.0 in. W.C. (3.5 kPa)

Orifice Size Center
Orifice Size Sides

See Table

See Table

Nominal Input
Rating

See Table

See Table

Electrical Rating

120 VAC, 60Hz less than 2 A. /

120 VAC, 60Hz less than 2 A. /

Gas Control

SIT

SIT

Altitude

0 - 4,500 ft. (0 - 1372 M)

0 - 4,500 ft. (0 - 1372 M)

Primary Air Opening

1/16” (3 mm) OPEN

1/4” (12 mm) OPEN

HIGH ALTITUDE INSTALLATION

When installing this appliance beyond 4500 ft. (1372 M) above sea level, the appliance must
be properly de-rated and installed according to local codes, in the absence of local codes, with
the current National Fuel Gas Code, ANSI Z223.1/ NFPA 54, in the US or Installation Code,
CAN/CGA-B149, in Canada.

«
...
3
4
5
6
7
...
»

Содержание 1060 Series













































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды