Nibart 1060 Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 44

Nibart 1060 Series Скачать руководство пользователя страница 31

Series 1060

31

REMOTE CONTROL SETUP AND OPERATION (SKYTECH)

Operation:

This function is not available on this model at this time.

Manual Flame Modulation - Main Flame:

Used to manually adjust main flame (#9 on display blinks)

Press

to activate flame adjustment.. Use

to adjust flame to desired level.

Upon initial start, to allow for proper burn ignition, the main flame will come on at the highest level. After 5 seconds the flame
will modulate down to last level before the unit was turned off.

Manual Flame Modulation - Rear Flame:

(#8 on display)

Fan Mode:

Manual control of fan speed (#7 on display blinks)

Press

to activate fan adjustment. Use

to adjust fan higher or lower.

The fan has a 5 min “delayed on” function to allow the firebox to warm up before air flow begins. On shut down, the fan will
run for 12min to cool down the fireplace before turning off.

Fan Default

The first time the system is used, the fan will “default” to a setting of (3). This would also be the case if the batteries were
removed long enough to loose it’s internal memory.
If the user changes the fan speed during operation, then turns the fireplace off. The next time the fireplace is cycled on, the
fan will adjust to the last know setting.

Lighting Mode:

(#10 on display)

This function is not available on this model at this time.

Mode:

Used to turn the fireplace On/Off, Thermostat and Countdown mode.(#12 on display)

Press and release to cycle the fireplace through the different modes.

«
...
29
30
31
32
33
...
»

Содержание 1060 Series













































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды