Nibart 1060 Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 44

Nibart 1060 Series Скачать руководство пользователя страница 10

Series 1060

10

Installation Instructions

Horizontal Installation
The horizontal run must have a 1/4” rise on an exterior wall and
must meet all local and national building codes, and must not be
easily blocked or obstructed. Termination clearances are as
follows (see Figure 16):

A.

Clearance above ground, verandah, porch, deck, or balco-
ny: 12” minimum (30 cm.)

B.

Clearance to a window or door that may be opened: 9”
minimum (23 cm)

C.

Vertical  clearance  to  a  ventilated  soffit  located  above  the
termination  within  a  horizontal  distance  of  2  feet  from  the
centerline  of  the  termination:  18”  minimum  (46  cm).

Note:

Clearances are to be in accordance with local installa-
tion codes and the requirements of the gas supplier.

D.

Clearance to an unventilated soffit: 12” minimum (30 cm).

Note: Clearances are to be in accordance with local
installation codes and the requirements of the gas
supplier.

E.

Clearance to an outside corner: 9” (23 cm).

Note: Clear-

ances are to be in accordance with local installation
codes and the requirements of the gas supplier.

F.

Clearance to an inside corner: 9” (23 cm).

Note: Clear-

ances are to be in accordance with local installation
codes and the requirements of the gas supplier.

G.

Do not install above a meter/regulator assembly within 3
feet (90 cm) horizontally from the centerline of the meter/
regulator.

Note: Clearances are to be in accordance

with local installation codes and the requirements of
the gas supplier.

H.

Clearance to a service regulator vent outlet: 6’ minimum
(1.8 m)

I.

Clearance to a non-mechanical air supply inlet to a building
or the combustion air inlet to any other appliance: 12” mini-
mum (30 cm)

J.

Clearance to a mechanical air supply inlet: 6’ minimum (1.8
m)

K.

Clearance above paved sidewalk or paved driveway locat-
ed on public property: refer to local code

L.

Clearance under open verandah, porch, deck, or balcony:
12” minimum (30 cm).

Note: Clearances are to be in ac-

cordance with local installation codes and the require-
ments of the gas supplier.

M.

Maximum horizontal run 5’ after 2’ vertical rise. Liquid Pro-
pane gas 5’ horizontal run to 35’ vertical rise. Natural Gas
maximum 35’ horizontal run with 7’ vertical rise.

Note:

Clearances are to be in accordance with local installa-
tion codes and the requirements of the gas supplier.

Figure 7 – Vent Termination Locations

«
...
8
9
10
11
12
...
»

Содержание 1060 Series













































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды