Nibart 1060 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 44

Nibart 1060 Series Скачать руководство пользователя страница 16

Series 1060

16

INITIAL OPERATION

1. Check that the appliance is properly vented and connected to the gas supply.
2. Check that all external parts, such as door and faceplate are properly attached and

fastened.

3. Do not operate this appliance with broken, cracked glass doors or without the door (s) in its

correct (and latched) position. Do not abuse the glass by either striking or slamming shut.

4. Check that there are no fingerprints left on glass panels, as high temperature can bake

these prints on permanently.

FINAL INSTALLATION CHECK

Each Nibart Custom Gas Fireplace is checked and tested at the factory prior to being pack-
aged and shipped to our dealers and finally installed in your home. Nibart recommends that
before leaving this unit with the customer, the installer must ensure that the appliance is firing
correctly and that the electrical system is in working order.

This will include:

1. Perform leak tests of supply line, gas control valve, supply line from gas control valve and

pilot assembly.

2. Clocking the appliance to ensure the correct firing rate

(see page 9 of this manual).

3. If required, adjusting the primary air to burner to ensure that the flame does not carbon or

soot.

4. Check for proper operation including correct drafting.

As a reminder, a TAG is attached to all of our gas fireplaces. This TAG is located at the gas
control valve. See Fig ?.

Any alteration to the product that causes carboning or sooting that results in any
damage or requires cleaning is not the responsibility of the manufacturer.

NIBART CUSTOM INDUSTRIES LTD.

*** INSTALLER ***

IMPORTANT NOTICE

ALL GAS AND ELECTRICAL CONNECTIONS

** MUST ** BE CHECKED AND TESTED AT

TIME OF INSTALLATION.

Fig ?.

«
...
14
15
16
17
18
...
»

Содержание 1060 Series













































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды