manualshive.com logo in svg

NI Climbing Frames Titanic, Инструкция по эксплуатации

Поделиться
Скачать
NI Climbing Frames Titanic Скачать руководство пользователя страница 8

Tools needed:  

•

 

Cordless drill 

•

 

Handsaw 

•

 

Spirit Level 

•

 

Hammer  

•

 

Shovel 

•

 

Stepladder 

•

 

Pencil 

•

 

Measuring tape 

•

 

10mm Hex bit 

•

 

PZ 2 Drill Bit 

 

Ground Preparation 

1.

 

Lay out the base and slide in the position that you intend the climbing frame to be placed. 
Ensure the base is parallel of any buildings, fences etc. that you are wishing to match in with. 
This will give you the size of the footprint the frame will take up in the garden.  

2.

 

Allow for at least 1.8m clearance beyond the end of the slide and 1.2m clearance for the 
steps, rock wall. 

3.

 

Once you are happy that the layout is correct, remove the slide.  

4.

 

Mark out clearly the centre of all 4 cut outs of both bases. Once these are marked you can 
lift the bases out of your way and then dig your holes. 

5.

 

If the climbing frame is on a level surface, 

then dig the holes at a diameter of 12” and depth 

12”. The tricky part is when the surface is uneven; in this case you woul

d have to 

compensate for the slope by making some holes deeper or shallower than others (minimum 

depth of 10”). The bottoms of all holes need to be level.

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание Titanic













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды