NFT BusView Скачать руководство пользователя страница 10

Activating the NFT-2600 Unit 

Prior to the initial powering of the unit, move the vehicle outside, so that the GPS 
receiver can receive signals from the GPS satellites. 
Upon initial power up of the NFT-2600 the LEDs start flashing on the front side of 
the unit to determine if the unit is powered on. If the LED is not flashing after 60 
sec, check the power connections. The statuses of the LED’s are below. 

 

Status LED Definitions 

Orange LED Status 

GSM/GPRS Cellular Communications 

Green LED Status 

GPS Communications 

Blinking – Tracker on, searching for wireless signal 

Blinking – GPS on, searching for satellite 
signal 

Patterned Blinking – Signal acquired, unit trying to 
establish connection to the communication server 

  

Solid – 2-way communication link with the 
communication server established 

Solid – GPS lock established 

 

After the unit has been powered for 5 to 15 minutes, the unit will send in a 
“power-up” message. 
While waiting for the power-up message, collect the following information before 
calling in (855-438-4771 option 2) for activating the unit: 

Account ID 
Vehicle Name 
Device IMEI number 
 

Please verify with tech support that the device has been activated and is working 
properly before putting the unit back in service. 
 
 
 

 

Confidential

Page 10

3/6/2020 

Содержание BusView













Отзывы: