Nexo PS Series Скачать руководство пользователя страница 36

Страница: 36 / 82

Page 36/82

ERIES HARDWARE SETUP PROCEDURE

Horizontal (PS15R2 only)



Remove the four TORX screws holding connector plates on both side of PS15R2;



Remove the connector plates from PS15R2;



Fill each screw hole with Locktite 243 or equivalent;



Position external plates from VNI-LBRK kits and secure them using the shoulder screws
supplied with these kits;



Posit

ion “L” brackets from VNI-LBRK kits, and secure them to the cabinet using the 4 remaining

shoulder screws supplied with these kits.



Slings and shackles (not provided) are required to secure the cluster under the ceiling;

CABLE SUSPENSION MOUNTING PROCEDURE FOR PS15R2

7.3.4 PS10R2 and PD15R2 wall suspension (vertical or horizontal)

Required item

Vertical



1 VNI-WS10 for PS10R2



1 VNI-WS15 for PS15R2



4 x 12mm diameter screws (

not provided

)

Horizontal



1 VNI-WS10 and 1 VNI-UBRK10 for PS10R2



1 VNI-WS15 and 1 VNI-UBRK12 for PS15R2



4 x 12mm diameter screws (

not provided

)

IMPORTANT
Ensure that the wall is strong enough to hold 4 times PS cabinet weight and that the
screws 12mm diameter and corresponding plugs required to fix the VNI-WS on the wall
are properly dimensioned.

Содержание PS Series



















































































Результаты поиска

Содержание PS Series

Отзывы:

Похожие инструкции для PS Series

Бренды по названию

Популярные бренды

Nexo PS Series, Руководство пользователя

Результаты поиска

Содержание PS Series

Отзывы:

Похожие инструкции для PS Series

Бренды по названию

Популярные бренды