background image

 

NEXO

 

A

NALOGUE 

PSTD

 

C

ONTROLLERS 

 

 

Page 53/82

 

 

 

 

8.5  TDcontroller REFERENCE GUIDE 

8.5.1  Linear section 

The characteristics of the linear section are independent of signal level, as opposed to the servo control 
functions described in next paragraph. 

Subsonic and VHF filtering 

Low  and  high-pass  filters  are  used  to  remove  signals  out  of  the  usable  frequency  range,  eliminating 
sub-  and  ultra-sonic  components  that  could  possibly  degrade  the  performance  of  the  Controller  and 
amplifiers. These filters are optimized to realize the overall target system response. 

Equalizing acoustical response 

This  equalization  section  provides  the  required  correction  to  obtain  a  flat  system  response,  as  the 
cabinets are acoustically designed for maximum efficiency in the whole frequency range. Active rather 
than passive attenuation allows amplifier voltages to be lowering for a given output SPL and therefore 
increases the maximum SPL achievable with the same amplifier. 

Active  equalization  also  extends  system  bandpass,  especially  at  low  frequencies  where  acoustical 
performance is limited by cabinet size. 

PS / Subbass Cross-Over 

From input signals summed together, the resulting mono signal is low-pass filtered to feed the SubBass 
channel. When  the  channel  is  turned  on  (Subbass  On),  main  channels  (Left  &  Right)  high-pass  filters 
are reconfigured to filter out signal components below the crossover frequency. Slopes and other filter 
characteristics are optimized using techniques optimized for the actual acoustical data of each driver. 

8.5.2  Servo Control section 

Servo  control  of  the  PS  TDcontroller  is  intended  to  work  with  amplifier  return  signals  present  at  the 
Sense inputs (monitored by front panel LEDs). 

VCAs and VCEQs 

Each  of  the  3  Audio  channels  (Left,  Right  and  SubBass)  contains  two  voltage  controlled  elements 
driven by servo signals: 

 

One operates on the whole frequency range (wide band VCA). 

 

The other elements work selectively as dynamic equalizers (LF-VCEQ & HF-VCEQ). 

Depending on the nature and origin of the servo signals, either one or the 3 combined elements is used 
to process the Audio signal. This feature allows more efficient processing while reducing audible effects. 

Содержание PS Series



















































































Отзывы: