Nexans Euromold K489TB/G Скачать руководство пользователя

Страница: 9 / 9

INSTALLATION OF THE CAP

CONNECTOR EARTHING

AND CABLE CLAMPING

NOTE :

A connector/bushing mated combination should not be allowed to carry the full weight of the cable.

Therefore it is necessary to clamp the cable as close as possible to the connector.

IMPORTANT NOTES :

- Never disconnect the connector from energised equipment nor energise a disconnected connector

without previously installing on its appropriate corresponding mating part.

- Do not allow hydrocarbon oils or solvents to contaminate the E.P.D.M. rubber.

In the event of contamination, wipe the surface clean with a dry cloth.

a Nexans company

Nexans Network Solutions NV - div. EUROMOLD

Zuid III - Industrielaan 12

B-9320 EREMBODEGEM-AALST – BELGIUM

Tel: +32 (0)53/85 02 11 – Telefax: +32 (0)53/83 10 13

[email protected]

protective

cap

nylon vent

rod

Installation on insulating plug :

- Clean the inside of the cap and the outside surface of

the connector and insulating plug.

- Place the nylon vent rod along the insulating plug

(see fig.) to exhaust the air during assembly of the cap.

- Push the cap over the connector and on to the

insulating plug.

- Press the centre of the cap on to the locking point

until it snaps in place. Press the cap on all sides to

make sure it is well positioned over the connector.

Position the cap with the pulling tab pointing

downwards.

- Remove the nylon vent rod.

system

earth

cable

clamp

screen

wires

Bend back the screen wires along the outer

sheath to form a pig tail.

Connect the earthing lead and screen wires to

the system earth.

earthing

lead

Page 9 of 9

IS91374-ENG - 489TB/G

-45/S - Revision 1

FOR INFORM

ATION ONL

Please alw

s use the instruc

tions supplied in the k

Содержание Euromold K489TB/G










Результаты поиска

Содержание Euromold K489TB/G

Отзывы:

Похожие инструкции для Euromold K489TB/G

Бренды по названию

Популярные бренды

Nexans Euromold K489TB/G, Руководство по установке

Результаты поиска

Содержание Euromold K489TB/G

Отзывы:

Похожие инструкции для Euromold K489TB/G

Бренды по названию

Популярные бренды