NewMar Guided Wave 12-1200IC Скачать руководство пользователя страница 16

U.S.A. HEADQUARTERS

P.O. Box 1306, Newport Beach, CA 92663

Phone: 714-751-0488  Fax: 714-957-1621

E-Mail: [email protected]

EURO WAREHOUSE

Phone:+31-35-603-2494  Fax:+31-35-603-2149

E-Mail: [email protected]

www.newmarpower.com

16

normal operation, and when properly installed. It is also protected, however, by an
internal thermal switch which shuts the unit completely off when it gets too hot. This
is typically due to being located in a high temperature area or a small enclosure
which restricts air flow, or due to a blockage of the air intake of the cooling fan. En-
sure free flow of air around and into the unit. Relocate it if necessary. 

Note

: The ther-

mal switch is self-resetting, so the inverter/charger will automatically return to ser-
vice when it cools to a safe operating temperature. Nevertheless, thermal cycling of
this sort will shorten the life of the unit, and should not be allowed to continue if it is
noted.

VI)

SPECIFICATIONS

MODEL

12-1200IC

12-1799IC

24-1300IC

Inverter Output:

VAC

115V, 60 Hz.

115V, 60 Hz.

115V, 60Hz.

Watts (Surge)

3300

6000

3000

Watts (Cont.)

1200

1800

1300

Wave Type

Quasi-Sine

Quasi-Sine

Quasi-Sine

Inverter Input:

VDC

11-14

11-14

22-28

Max Amps

120

180

65

Charger Output:

VDC (@  Float)

13.8

13.8

27.6

Max Amps

50

65

25

Charger Input:

VAC

115V, 60 Hz.

115V, 60 Hz.

115V, 60Hz.

Max Amps

9

13

9

Weight: Lbs.

27

27

26

Case Size (all models):

H

W

D

7.5"

8.2"

15.0"

Internal Charger Type: 

Two stage; "Bulk/Float"

Operating Temperature (all models): 

-22° C to +40° C (0° F to 104°F)

Mechanical Features (all models):

l

Thermally controlled cooling fan

l

GFCI protected duplex outlets

l

Powder coated aluminum case with integral mounting flanges

l

Conformal coated printed circuit boards

Protection Features (all models):

l

Automatic low battery shutdown

l

Output circuit breaker

l

Auto high temperature shutdown/recovery

l

Short circuit protection

l

Overload protection

l

Current limiting (battery charger)

Содержание Guided Wave 12-1200IC




















Отзывы: