3
1. HANDSET ANTENNA
2. CHARGE CONTACTS:
For charging the BATTERY PACK inside the HANDSET. We recommend
cleaning the CHARGE CONTACTS periodically with a damp cloth.
3. TALK Button:
Press to answer an incoming call or to place a call. Press to end a call.
4
. VOLUME Button:
Press to select the receiver volume level (HI, MID, LOW). It
will remain at the last level set until you change it.
5. REDIAL/PAUSE Button:
(REDIAL) Press to redial the last number you dialed.
(PAUSE) Press to insert a pause while dialing. (You will need the REDIAL/PAUSE button to
dial numbers which use an alternative Long Distance Access Code.)
6. RINGER ON/OFF SWITCH:
Switch to ON to engage the ringer on the HANDSET. Set switch
to OFF
to disengage the ringer on the HANDSET.
7. HEADSET JACK:
For connecting your headset plug to enjoy hands free communication. (See
page 10 for detail).
8. MEMO Button:
Press to store phone numbers in memory or to call a number you have
previously stored.
9
. TELEPHONE KEYPAD:
Allows you to make a call depending on pressed button.
10. FLASH Button:
Press to answer an incoming call if you have Call Waiting.
11. SCAN Button:
Press to change the operating channel when you hear interference.
12. IN USE/BATT LOW LED Indicator:
Lights up when the HANDSET is in TALK mode. Blinks
when the battery charge is low.
IMPORTANT
In order to get maximum life from the HANDSET
BATTERY PACK, be sure to charge the
HANDSET for 12 hours before initial use.
TALK
REDIAL/PAUSE
MEMO
SCAN
FLASH
VOLUME
HANDSET Controls
Problem Solving Section
For your assistance, we have listed below a few common problems.
Phone does not work, check the following:
1. BASE UNIT is plugged into a power source.
2. HANDSET is charged.
3. TONE/PULSE Select Switch is in the right position.
4. TELEPHONE LINE CORD is plugged into the TELEPHONE JACK.
Range of phone limited, check the following :
1. ANTENNA on the BASE UNIT is raised.
2. BASE UNIT is centrally located in your residence.
3. BASE UNIT is not located near appliances.
No dial tone, check the following:
1. TELEPHONE LINE CORD plugs are connected to the TELEPHONE JACK and
TELEPHONE LINE CONNECTION JACK.
2. BASE UNIT is plugged into a power source.
3. If you had a power failure or had unplugged the BASE UNIT, replace the HANDSET on the
BASE UNIT for 2 to 5 seconds to reset the system.
Received signal flutters or fades, check the following:
1. BATTERY PACK in the HANDSET is fully charged.
2. HANDSET is not too far from the BASE UNIT.
3. ANTENNA on the BASE UNIT is raised.
Interference on reception, check the following:
1. Noise may be picked up from electrical products in the home or electrical storms. Generally,
this noise is a minor annoyance and should not be interpreted as a
defect in your system.(See Technical Information on page 14.)
2. Choose an alternate channel using the button on the HANDSET.
Problem Solving
Excess static, check the following:
1. Check to see that the ANTENNA is not touching another metal object.
2. Raise or reposition the BASE UNIT ANTENNA.
If after pressing the button, you receive three "beeps" and no dial tone, check the following:
1. BASE UNIT is plugged into a power source.
2. It you had a power failure or had unplugged the BASE UNIT, replace the HANDSET on the
BASE UNIT for 2 to 5 seconds to reset the system.
NOTE:
If none of the telephones in the house are working, disconnect one set at a time to verify
that none of the telephones are causing the problem. If you still have a problem after doing this,
and your telephone still does not work, please contact your local phone company.
16
SCAN
TALK
