manualshive.com logo in svg

New Yorker CG-A 30, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
New Yorker CG-A 30 Скачать руководство пользователя страница 13

13

I.

Sequence of Operation, Continuous Ignition (Standing
Pilot).

1. Normal Operation

a. Thermostat calls for heat. Vent Damper opens.

b. Gas Valve energized allowing main gas flow and

ignition of Main Burners.

c

.

Call for heat ends. Gas Valve de-energized,
extinguishing main flame. Vent Damper closes.

2. Safety  Shutdown

a. Limit: Automatically interrupts main burner

operation when water temperature exceeds set
point. Maximum allowable temperature is 250°F.
Circulator continues to operate with call for heat
and Vent Damper closes. Normal operation
resumes when water temperature falls below set
point.

b

.

Blocked Vent Switch. Automatically interrupts
main burner operation when excessive vent
system blockage occurs. Circulator continues to

operate and Vent Damper remains open with call
for heat. If blocked vent switch is activated do
not attempt to place boiler in operation. The
source of blockage must be corrected by trained
and skilled personnel from a qualified service
agency before resetting switch.

c

.

Flame Roll-out Switch. Automatically interrupts
boiler operation when flames or excessive heat
are present in vestibule. Circulator continues to
operate and Vent Damper remains open with call
for heat. Control is single use device. If flame roll-
out switch is activated do not attempt to place
boiler in operation. The source of blockage must
be corrected and the flame roll-out switch
replaced by trained and skilled personnel from a
qualified service agency.

d

.

Thermocouple: senses pilot flame and causes gas
valve to turn off main burner and pilot burner gas
flow should pilot burner flame extinguish.
Circulator continues to operate and Vent Damper
remains open with call for heat.

Figure 12: Wiring Diagram, Continuous Ignition (Standing Pilot)

Содержание CG-A 30





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды