background image

NRP1004 Series IP Phone                                                                        User Manual 

www.newrocktech.com                                                                                                                                                                      2-1 

Initial Connection and Settings 

2.1 Power and Network Connections 

2.1.1 Connecting to a Network 

Prior to the configuration, make sure that broadband Internet access services are available in the current 

environment.  

With a broadband router 

Establish connections between the network hardware by connecting one end of the network cable to the 

WAN port of the IP phone and the other end to the LAN port of your broadband router. In most cases, 

configure your network settings to DHCP mode. 

 

 

Without a broadband router 

Establish connections between the network hardware by connecting one end of the network cable to the 

WAN port of the IP phone and the other end to the LAN port of your broadband modem. If a TV cable 

broadband is used, in most cases, you need to set the network mode of your IP phone to DHCP. If 

ADSL is used, you need to set the network mod to PPPOE. 

   

 

With a substitute broadband router 

NRP1004/P itself has the broadband routing capability. As long as the WAN port of the NRP1004/P is 

properly connected to the broadband modem and the LAN port of the NRP1004/P is connected to your 

computer or other devices with Internet capability, you can access the Internet. 

Содержание NRP1004 Series






























































































Отзывы: