New Leader L4000 G4 Скачать руководство пользователя страница 74

Страница: 74 / 102

www.NewLeader.com

(800) 363-1771

307074-AA-I

L4000G4

Lubrication & Maintenance Chart

Shut off all power and allow all moving parts to come to rest before performing any

maintenance operation� Failure to comply with this warning could result in death or serious

injury�

The spreader should be regularly lubricated with the lubricants recommended in this manual in accordance

with the following chart:

Location

Places

Method

Frequency

Hydraulic System

Reservoir

Check Daily� Change Annually

Filter

Check daily; Change when indicated (Red)

Conveyor

Dragshaft Bearings (A)

Grease Gun

Weekly

Idler Shaft Bearings (B)

Grease Gun

Weekly

Take-Up Screws (C)

Hand Grease

Weekly

Snubber Pulley Bearings (D)

Grease Gun

Weekly

Gearcase

Gear Oil

Check Monthly; Change

Annually

Feedgate

Jack Assembly (E)

Grease Gun

Annually

Spinner Assembly

Jack Assembly (F)

Grease Gun

Weekly

Bin 2 Conveyor

Dragshaft Bearings (G)

Grease Gun

Weekly

Idler Shaft Bearings (H)

Grease Gun

Weekly

Take-Up Screws (J)

Hand Grease

Annually

Conveyor Chain Strands

Oil Mixture

Bi-Weekly

Spray

Lubricant

Annually

NOTE: Unusual conditions, such as excessive dust, temperature extremes or excessive moisture may

require more frequent lubrication of specific parts.

*See “Lubricant and Hydraulic Oil Specifications” for types of lubricants and oil to be used.

Spray MULTAPPLIER/MULTIBIN conveyor chain with Fluid Film™ spray lubricant or equivalent�

Chain Conveyors

Use a mixture of 75% No� 1 or No� 2 diesel fuel or kerosene mixed with 25% SAE 10 engine oil in the

main unit conveyor chain oiler�

Содержание L4000 G4







































































































Результаты поиска

Содержание L4000 G4

Отзывы:

Похожие инструкции для L4000 G4

Бренды по названию

Популярные бренды

New Leader L4000 G4, Руководство оператора

Результаты поиска

Содержание L4000 G4

Отзывы:

Похожие инструкции для L4000 G4

Бренды по названию

Популярные бренды