New Leader L4000 G4 Скачать руководство пользователя страница 31

Страница: 31 / 102

- 31 -

L4000G4

www.NewLeader.com
(800) 363-1771

307074-AA-I

Hydraulic Hose Installation

Do not overtighten a threaded connection, the fitting or housing into which the fitting

is placed could be distorted and an unstoppable leak could occur� Failure to follow this

requirement may result in injury or machine damage�

Do not use one manufacturer’s hose with another manufacturer’s fittings! Such will void

any warranty and may cause premature burst or leak of hydraulic fluids! Failure to comply

with this requirement could result in death or serious injury�

Determine pressure port of pump� Install pressure hose into this port as shown in Figure 6� Connect

suction hose to opposite port and to tank outlet on hydraulic tank� Use plastic tie straps as necessary to

Hydraulic Pump Installation

HECO pumps are direct mount� See “Pump Hydraulics” in the spreader parts manual for assembly

instructions�

Figure 6 - Hydraulic Pump Installation

Use thread sealer on all NPT fittings. When using thread sealer, do not put it on the first three threads

of the fitting. Too much on the fitting or on the first three threads will force it into the oil stream where it

could damage the system�

Assemble system as shown in “Hydraulics” parts list in the parts manual� Place hose clamps as needed

to keep hoses away from hot or moving parts� Do not let hoses hang so low as to be snagged� Do not

stretch hoses tight�

Hydraulic hoses are as follows:

• Pressure Line: High pressure hose supplied by dealer� Hose must have minimum pressure rating

that corresponds to the maximum pressure setting of the hydraulic system� Refer to “Hydraulic

Requirements” on page 25�

• Suction Line: Suction hose supplied by dealer� Hose must meet or exceed SAE 100R4 requirements�

Installation

Содержание L4000 G4







































































































Результаты поиска

Содержание L4000 G4

Отзывы:

Бренды по названию

Популярные бренды

New Leader L4000 G4, Руководство оператора

Результаты поиска

Содержание L4000 G4

Отзывы:

Бренды по названию

Популярные бренды