manualshive.com logo in svg

New Holland W190D, Руководство по обслуживанию

Поделиться
Скачать
New Holland W190D Скачать руководство пользователя страница 58

Engine - Engine and crankcase

Engine - Install

WARNING

Hot liquid under pressure!
Never remove the filler cap or the recovery tank cap while the engine is running or the coolant is hot.
Let the system cool. Turn the filler cap to the first notch and allow any pressure to escape, and then
remove the filler cap. Loosen the recovery tank cap slowly to allow any pressure to escape.
Failure to comply could result in death or serious injury.

W0296A

NOTE:

emissions sensors mounted in the exhaust stream are sensitive to extreme vibrations. Use of tools that gen-

erate extreme vibrations, such as impact wrenches and hammers, will result in damage to emission sensors. Avoid
using these tools during any service procedure in close proximity of emission sensors. If the use of these tools cannot
be avoided, remove the sensors using extreme caution prior to performing any service procedure.

RAIL12WEL0130FA

1

1. Engine mount bolt

5. Washers

2. Washer

6. Washer

3. Upper isolator

7. Nut

4. Lower isolator

8. Remote oil drain hose

1. Inspect the engine mounts. If the engine rubber isola-

tors require replacement, remove and discard the up-
per isolators

(3)

and lower isolator

(4)

.Install new upper

isolators

(3)

and new lower isolators

(4)

.

48144035_EN 03/07/2017

10.1 [10.001] / 25

Содержание W190D






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды