background image

INTRODUCTION

Battery

Batteries give off explosive gases.

Never handle open flames and unshielded light sources
near batteries. (No smoking is addressed in the next in-
struction).

To prevent any risk of explosion, observe the following
instructions:

• When disconnecting the battery cables, always discon-

nect the negative (-) cable first.

• To reconnect the battery cables, always connect the

negative (-) cable last.

• Never short-circuit the battery terminals with metal ob-

jects.

• Do not weld, grind or smoke near a battery.

Battery electrolyte causes severe burns. The battery con-
tains sulphuric acid. Avoid any contact with the skin, eyes
or clothing.

TULI12WEX2015AA

11

Treatment:

• EXTERNAL: Rinse well with water, removing any soiled

clothing.

• INTERNAL: Avoid vomiting. Drink water to rinse your

mouth. Consult a doctor.

• EYES: Rinse abundantly with water for

15 min

and con-

sult a doctor.

• When the electrolyte of a battery is frozen, it can ex-

plode if you attempt to charge the battery or if you try to
start the engine using a booster battery. Always keep
the battery charged to prevent the electrolyte freezing.

Provide good ventilation when changing a battery or using
a battery in an enclosed space. Always protect your eyes
when working near a battery.

TULI12WEX2016AA

12

Never set tools down on the battery. They may induce
a short circuit, causing irreparable damage to the battery
and injuring persons.

Never wear metal necklaces, bracelets or watch straps
when working on the battery. The metal parts may induce
a short circuit resulting in burns.

Dispose of used batteries separately from other waste in
the interests of environmental protection.

TULI12WEX2017AA

13

48144035_EN 03/07/2017

9

Содержание W190D






























































Отзывы:

Похожие инструкции для W190D