manualshive.com logo in svg

New Holland W190D, Руководство по обслуживанию

Поделиться
Скачать
New Holland W190D Скачать руководство пользователя страница 25

INTRODUCTION

Basic instructions - Electrical equipment precautions

WARNING

Battery acid causes burns. Batteries contain
sulfuric acid.
Avoid contact with skin, eyes or clothing. An-
tidote (external): Flush with water. Antidote
(eyes): flush with water for 15 minutes and
seek medical attention immediately. Antidote
(internal): Drink large quantities of water or
milk. Do not induce vomiting. Seek medical
attention immediately.
Failure to comply could result in death or se-
rious injury.

W0111A

• The disassembly of electrical equipment is not allowed.

• Handle equipment with care so as not to drop it or bump

it.

• Connector should be removed by unlocking while hold-

ing the connector.

• Never disconnect electrical plugs by pulling on the

wires.

Always use only the electrical connectors to

make the disconnection.

• Check that connector is connected and locked com-

pletely.

• Engine key off before removing and connecting connec-

tor.

• Engine key off before touching terminals of starter and

alternator.

• Wash machine with care so as not to splash water on

electrical equipment and connector.

• If water has entered a sealed connection, thoroughly

dry both connectors before reconnecting

• Remove battery grounding terminal before beginning

work close to battery and battery relay with tools.

48144035_EN 03/07/2017

18

Содержание W190D






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды