New Holland CR9090 Tier 4a Скачать руководство пользователя страница 57

Страница: 57 / 81

Engine - Engine and crankcase

12. From inside the grain tank, connect the lower coolant

hose

(1)

to the engine. Secure with the hose clamp

(2)

and tighten securely.

40015959_855

13. Connect the heater hoses

(1)

to the engine and tighten

the hose clamps

(2)

securely.

40015959_856

14. From inside the grain tank, install the rotary screen

brush drive belt

(1)

onto the pulley

(2)

and engine

crankshaft pulley. Turn the pulley adjusting bolt

(3)

clockwise to adjust the belt tension until the belt is
tight. Tighten the lock nuts on the carriage bolts

(4)

when the belt is properly adjusted.

40015956_862

15. Install the air conditioning compressor

(1)

on the en-

gine and secure with the mounting bolts

(2)

Tighten

the bolts securely.
Connect the electrical connectors

(3)

to the compres-

sor wires.

16. Install the main drive belt onto the engine.

40015211_863

47695751 27/03/2014

10.1 [10.001] / 15

Содержание CR9090 Tier 4a


















































































Результаты поиска

Содержание CR9090 Tier 4a

Отзывы:

Похожие инструкции для CR9090 Tier 4a

Бренды по названию

Популярные бренды

New Holland CR9090 Tier 4a, Руководство по обслуживанию

Результаты поиска

Содержание CR9090 Tier 4a

Отзывы:

Похожие инструкции для CR9090 Tier 4a

Бренды по названию

Популярные бренды