New Holland CR9090 Tier 4a Скачать руководство пользователя страница 48

Страница: 48 / 81

Engine - Engine and crankcase

15. Loosen the clamps

(1)

and remove the air pipe

(2)

16. Loosen the clamp

(3)

and disconnect the water hose

from the cooling system.

ZEIL09CR0252A0B

17. Remove the main drive belt

(1)

from the engine.

18. Disconnect the electrical connectors

(1)

ATTENTION:

Do not disconnect any of the air conditioning

lines or hoses during compressor removal, as serious in-
jury could result.

19. Remove the mounting bolts and nuts

(2)

from the air

conditioning compressor

(3)

Remove the compressor from the engine and tie the
assembly out of the way.

10013117

20. From inside the grain tank, loosen the mounting nuts

on the carriage bolts

(1)

and turn the rotary screen

drive pulley adjusting bolt

(2)

counter clockwise, to

release the tension on the drive belt

(3)

. Remove the

drive belt.

10013118

47695751 27/03/2014

10.1 [10.001] / 6

Содержание CR9090 Tier 4a


















































































Результаты поиска

Содержание CR9090 Tier 4a

Отзывы:

Похожие инструкции для CR9090 Tier 4a

Бренды по названию

Популярные бренды

New Holland CR9090 Tier 4a, Руководство по обслуживанию

Результаты поиска

Содержание CR9090 Tier 4a

Отзывы:

Похожие инструкции для CR9090 Tier 4a

Бренды по названию

Популярные бренды