Neuropace NeuroPace CL-315-10 Скачать руководство пользователя страница 35

Страница: 35 / 112

Surgical Procedures

RNS

System User Manual

URGICAL

ROCEDURES

Implanting physicians should have adequate experience in the implantation of subdural and stereotactic

implantation of intraparenchymal electrodes, in the surgical treatment of intractable epilepsy, have

completed the NeuroPace

RNS

System training program, and be thoroughly familiar with all product

labeling.

-I

MPLANT

Patient and Family Information

The potential risks and benefits of implanting the RNS

System and responsive electrical

stimulation therapy should be discussed with the patient, legal guardians, and family members

before the implant procedure and during follow-up. The patient should be counseled that

diathermy procedures, Magnetic Resonance Imaging (MRI) procedures, Electroconvulsive

Therapy (ECT) and Transcranial Magnetic Stimulation (TMS) are contraindicated, even if the

neurostimulator is turned off or has been removed, or if any leads or any part of a lead remain.

The patient should also be counseled on other medical procedures to avoid and on RNS

System

care and environmental hazards. The RNS

System Patient Manual outlines this information and

should be provided to and reviewed with the patient prior to the RNS

System implant.

Pre-surgical Antibiotics

To reduce the risk of infection, it is recommended that antibiotics be administered prior to surgery.

Product Preparation

1. Order and obtain the RNS

Neurostimulator and appropriate lead(s) for the implant, as

determined in the surgical planning for this procedure.

Before opening the RNS

Neurostimulator and leads packaging, verify model numbers, use-

by dates and product sterility

3. It is recommended that additional products be available in case product sterility or function is

compromised.

Number of Leads

A maximum of four leads may be implanted, only two of which may be depth leads. Only two

leads may be connected to the neurostimulator at any time; it is recommended that a unique

identifier be attached to each lead.

Programmer Preparation

The programmer should be in the operating room. It is used for the following activities:

•

Assigning lead type(s) and serial number(s) to the corresponding neurostimulator port(s).

•

Programming the montage, detection and ECoG storage.

•

Confirming lead integrity by performing lead impedance measurements.

•

Viewing real-time ECoGs to verify sufficient lead-tissue contact.

•

Troubleshooting neurostimulator and lead issues.

Содержание NeuroPace CL-315-10

















































































































Результаты поиска

Содержание NeuroPace CL-315-10

Отзывы:

Бренды по названию

Популярные бренды

Neuropace NeuroPace CL-315-10, Руководство пользователя

Результаты поиска

Содержание NeuroPace CL-315-10

Отзывы:

Бренды по названию

Популярные бренды