Neumo 66TX51341313131 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 92

background image

Container Cleaning System TANKO®EX-R64T

1 Introduction

Translation - Operating/installation instructions 2020/03

1/80

1

Introduction

These operating/installation instructions (referred to hereinafter as instructions) are an integral part of the
device. They provide you with all the information required for smooth operation of the TANKO

®

EX-R64T

cleaning system (referred to hereinafter as the device).

The instructions must be read, understood, and applied by all persons assigned to carry out installation
and assembly, start-up, maintenance, cleaning and troubleshooting of the device. This applies in
particular to the safety instructions listed.

After studying the instructions, you will be able to

–

install and operate the device safely,

–

clean and service the device correctly and

–

take the correct action if a fault occurs.

In addition to these instructions, generally applicable, statutory and other binding regulations for the
prevention of accidents and for environmental protection in the country of use must also be observed.

The instructions must be kept at the place of use of the device so that they are available in legible condition
at all times. If the device is resold, the instructions must always be passed on to the new owner.

Download the instructions, if nec., from the website:

http://www.awh.eu/de/downloads

1.1

Means of Representation

1.1.1

Explanation of Signal Words

The warnings are introduced by a signal word that describes the extent of the hazard. Their meaning
and their classification in hazardous situations are explained in the following overview.

Signal Word

Meaning

Consequences of Failure to Observe

DANGER

Hazard with a high level of risk

Death or severe physical injury

WARNING

Hazard with a moderate level of risk Death or severe physical injury

CAUTION

Hazard with a low level of risk

Minor or moderate physical injury

NOTE

Hazard with a low risk

Risk of material damage

NOTE ON
EXPLOSION
PROTECTION

Important note on explosion
protection

Loss of explosion protection and resulting
hazards

Table 1.1-1: Overview of signal words

«
...
7
8
9
10
11
...
»

Содержание 66TX51341313131





























































































Отзывы:

Нет отзывов

Похожие инструкции для 66TX51341313131

Бренд: ABB Страницы: 11

Бренд: Campden instruments Страницы: 8

Бренд: GE Страницы: 14

Бренд: GE Страницы: 11

Бренд: GE Страницы: 20

Druck ADTS 2 Series

Бренд: GE Страницы: 18

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Gamry Instruments Страницы: 69

Бренд: Gamry Instruments Страницы: 30

Бренд: Gamry Instruments Страницы: 88

Бренд: Rayger Страницы: 2

Бренд: Quantum Страницы: 11

Бренд: Quanser Страницы: 21

Бренд: Quanser Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды