manualshive.com logo in svg

NETGEAR N450 WNR2500, Руководство пользователя, Страница: 119 / 143

Поделиться
Скачать
NETGEAR N450 WNR2500 Скачать руководство пользователя страница 119

Monitoring

119

 N450 Wireless Router WNR2500

•

Domain Name Server

. The Domain Name Server address that the router uses. A 

Domain Name Server translates human-language URLs such as www.netgear.com into 
IP addresses.

Statistics

The router provides various statistics.

To view the traffic statistics:

1.

Click the 

ADVANCED

 tab.

The Router Status screen displays. 

2.

In the Internet Port pane, click the 

Show Statistics

 button.

A pop-up screen displays traffic statistics:

The following information displays:

•

System Up Time

. The time elapsed since the router was last restarted.

•

Port

. The statistics for the WAN (Internet) port, the four LAN (Ethernet) ports 

combined, and the wireless LAN (WLAN) port.

•

Status

. The link status of the port.

•

TxPkts

. The number of packets transmitted on this port since reset or manual clear.

•

RxPkts

. The number of packets received on this port since reset or manual clear.

•

Collisions

. The number of collisions on this port since reset or manual clear.

•

Tx B/s

. The current transmission (outbound) bandwidth that is used on the port.

•

Rx B/s

. The current reception (inbound) bandwidth that is used on the port.

•

Up Time

. The time elapsed since this port acquired the link.

•

Poll Interval

. The interval at which the statistics are updated on this screen. 

3.

To change the polling frequency, enter a time in seconds in the Poll Interval field, and click 
the 

Set Interval 

button.

4.

To stop the polling entirely, click the 

Stop

 button.

Содержание N450 WNR2500
















































































































































Отзывы:

Нет отзывов