Model FB104 100 Mbps Network Starter Kit Installation Guide
© 2000 by NETGEAR, Inc. All rights reserved.
Trademarks
NETGEAR™ is a trademark of NETGEAR, Inc. Windows® is a registered trademark of Microsoft Corporation. Other brand and product names are trademarks or registered
trademarks of their respective holders. Information is subject to change without notice.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document
without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the Model FA310TX Network Card and the Model FE104 Fast Ethernet Hub have been suppressed in accordance with the conditions set out in the
BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in accordance with the regulations may, however, be subject
to certain restrictions. Please refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market and has been granted the right to test the series for
compliance with the regulations.
Voluntary Control Council for Interference (VCCI) Statement (For the Model FE104 Fast Ethernet Hub)
This equipment is in the first category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set by the Voluntary Control
Council for Interference by Data Processing Equipment and Electronic Office Machines that are aimed at preventing radio interference in commercial and/or industrial
areas.
Consequently, when this equipment is used in a residential area or in an adjacent area thereto, radio interference may be caused to equipment such as radios and TV
receivers.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice (For the Model FE104 Fast Ethernet Hub)
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference, in which case users will be required to take whatever measures may be necessary to correct the
interference at their own expense.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice (For the Model FA310TX Network Card)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, (2) This device must accept any interference received,
including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
EN 55 022 Statement (For the Model FE104 Fast Ethernet Hub)
This is to certify that the Model FE104 Fast Ethernet Hub is shielded against the generation of radio interference in accordance with the application of Council Directive 89/
336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class A (CISPR 22).
EN 55 022 Statement (For the Model FA310TX Network Card)
This is to certify that the Model FA310TX Network Card is shielded against the generation of radio interference in accordance with the application of Council Directive 89/
336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class B (CISPR 22).
Compliance is dependent upon the use of shielded data cables.
Note:
Modifications to this device change it from the original state it was in when tested and may alter the device so that
it no longer complies with FCC testing limitations for Class B digital devices. According to FCC regulations, the user
could be prevented from operating this equipment if it is modified.
Declaration of Conformity
NETGEAR Model FA310TX Network Card
FOR HOME OR OFFICE USE
Tested to comply
with FCC Standards
Warning:
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case,
the user may be required to take appropriate measures.
Содержание FB 104
Страница 1: ......
