NetComm NB6 Скачать руководство пользователя страница 69

Страница: 69 / 152

YML854 Rev1

NB6, NB6W, NB6Plus4W

User Guide

www.netcomm.com.au

Internet – Connections

To set WAN settings for each service, please open

Advanced

–

Internet.

This page allows you to edit, to

remove, or to add WAN settings.

If you click the

Connect

hyperlink under the PVC Name item, the system will connect to WAN automatically. If

the WAN connection is OK, you can check the detailed information directly.

You can add new PVC(s) by clicking the

Add

button, edit the settings for the present PVC by clicking

the

Edit

column, or delete the existing PVC by pressing

icon.

Adding a New One

To add a new WAN connection, please click the

Add

button. The following screen appears.

vPI (virtual Path Identifier):

Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255.
Please refer to the value that your ISP provides.

vCI (virtual Channel Identifier):

Identifies the virtual channel endpoints in an ATM network. The valid range is from 32 to 65535 (1 to
31 is reserved for well-known protocols). Please refer to the value that your ISP provides.

Содержание NB6

























































































































































Результаты поиска

Содержание NB6

Отзывы:

Похожие инструкции для NB6

Бренды по названию

Популярные бренды

NetComm NB6, Руководство пользователя

Результаты поиска

Содержание NB6

Отзывы:

Похожие инструкции для NB6

Бренды по названию

Популярные бренды