NetComm NB6 Скачать руководство пользователя страница 51

Страница: 51 / 152

YML854 Rev1

NB6, NB6W, NB6Plus4W

User Guide

www.netcomm.com.au

MTU: (refer to the WAN section)

The default

MTU

value for

LAN side Settings

is 1500. You may modify it if necessary.

DhCP Server On:

Check this item if DHCP service is needed on the LAN side. The router will assign IP address and
gateway address for each of your PCs.

Start IP Address & end IP Address:

Enter the information needed.

Lease Time:

Key in the duration for the time. The default is 1day.

DhCP Server Off:

Check this item if DHCP service is not needed on the LAN.

On this web page, the primary IP address and subnet mask will be shown. You can modify them if needed.

Key in all the necessary settings and click

You can check the contents on the

Summary

page.

If you find anything incorrect, click

Back

to modify the settings.

If everything is OK, click

Finish

to accept these settings.

Now, the system will reboot to activate the new settings that you have set in this section.

Please wait for 2 minutes before restarting the router.

Содержание NB6

























































































































































Результаты поиска

Содержание NB6

Отзывы:

Похожие инструкции для NB6

Бренды по названию

Популярные бренды

NetComm NB6, Руководство пользователя

Результаты поиска

Содержание NB6

Отзывы:

Похожие инструкции для NB6

Бренды по названию

Популярные бренды