raDIo DEvICE programmIng
Each of the zones of the ECO8x can be a radio zone. Once programmed, zones can
accept both radio devices and normal zone inputs simultaneously.
the optional 100–200 Ness Radio Interface is required for radio devices to operate.
A radio device is any type of Ness transmitter including Radio pIR, Radio Reed
switches, Radio smoke detector.
PROGRAMMING RADIO DEVICES
Up to 8 radio devices can be assigned to the ECO8x, (one per zone).
PROGRAMMING SEQUENCE – NO RESTORALS
suitable for 100–663 R15 Radio pIR, 100–691 R12 Radio pIR, 100–683 Radio pendant, 100–203
Radio smoke detector.
Select a zone using P01E – P08E
The ARMEd light will be oN if a Radio device is already programmed to the zone. Press 0E to delete.
Press 1E
The REAdY light will turn oN to indicate that the zone is ready to accept the Radio device.
Trigger the Radio Device
A. if the Radio device is accepted, the REAdY light will turn off, the ARMEd light will turn on and 3 beeps will sound.
B. if the REAdY light stays on and a warning beep sounds, the Radio device is already assigned to another zone and
must be cleared from that zone first.
C. if SUPERViSEd SiGNALS have also been successfully recognised, the TAMPER light will turn oN.
EXAmplE: to program a Radio pIR on zone 1:
p01E 1E
Trigger the Radio PiR (or simply connect the battery)
PROGRAMMING SEQUENCE – WITh RESTORALS
suitable for 100–662
Radio Reed Switch.
Alarm the reed switch, ie., move the magnet away from the switch
Leave the reed switch in the alarm condition and wait until radio transmission has stopped.
Select a zone using P01E – P08E
The ARMEd light will be oN if a Radio device is already programmed to the zone. Press 0E to delete.
Press 1E
The REAdY light will turn oN to indicate that the zone is ready to accept the Radio device.
Restore the reed switch (place the magnet next to the switch)
A. if the Radio device is accepted, the REAdY light will turn off, the ARMEd light will turn on and 3 beeps will sound.
B. The MEMoRY light will turn on to indicate that this device sends Restorals.
C. if the REAdY light stays on and a warning beep sounds, the Radio device is already assigned to another zone and
must be cleared from that zone first.
d. if SUPERViSEd SiGNALS have also been successfully recognised, the TAMPER light will turn oN.
EXAmplE: to program a Radio Reed switch with Restorals on zone 2:
Alarm the reed switch
P02E 1E
Restore the reed switch
DELETING A RADIO DEVICE:
Use P01E to P08E to select the zone
Press 0E to clear the device
(3 beeps will sound)
P01E – P08E
PROGRAM MODE LEVEL
Installer.
FACTORy DEFAULT
No Radio devices programmed.
NOTES
• Radio device programming is done by
automatically enrolling the radio code into
the control panel.
• Radio devices can only be deleted by
keypad.
• some Ness Radio devices send
separate Alarm and Restore signals.
• For special purposes, radio zones can
be also programmed to accept radio
keys. In this case the zone can not also
be programmed to accept a radio device.
TIP:
to prevent
conflicting radio signals
when programming
Radio devices, disable
each device once you have
finished programming it.
(Remove the battery or open the
RAdIO link).
Remember to enable all the
devices when programming is
completed.
RADIO DEVICES - OPTION TABLE
Zone 1
p01E
Zone 2
p02E
Zone 3
p03E
Zone 4
p04E
Zone 5
p05E
Zone 6
p06E
Zone 7
p07E
Zone 8
p08E
100–662
Ness Radio
Reed Switch
100–663
Ness R15 Radio PiR
RADIO PIR
100-663
100-691
R12 Radio PIR
100–691
Ness R12 Radio PiR
100–527
Ness Universal
Transmitter
the Ness R12 and R15 Radio pIRs have a tEst link which disables the re-transmit
timer, allowing the detector to be walk tested without waiting for the 4 minute re-
transmit timer to expire. If the tEst link is left on, the pIR will automatically revert
to normal mode after 30 minutes.
TEST mode can be re-started by briefly removing then replacing the battery.
48
N
ess
eCO8
x
C
ONtrOl
P
aNel
– I
NstallatION
M
aNual
nEss raDIo
