background image

 

 

I M P O RTA N T   S A F E G UA R D S

SAFETY INSTRUCTIONS 

WARNING:  Whenever using any equipment, 

always follow manufacturers’ 
instructions to ensure safe operation. 

 

CAUTION:  Read and make sure you understand 

these safety and operating guidelines. 

1.

 

Do not operate the machine until it is connected to 
a compatible power source. 

2.

 

Familiarize yourself with the layout of the control 
panels and with the operation of the lacquer system. 

3.

 

Operators should be trained on the proper use of 
the machine and all safety procedures. 

4.

 

Comply with all safety warning signs, labels and 
instructions. 

5.

 

Ensure that eye protection and clean towels are 
available for use during cleanup. 

6.

 

It is advisable to wear eye protection when 
filling/emptying the lacquer container.  Ensure that 
an approved emergency eyewash station is adjacent 
to the laminator. 

CAUTION:  Prior to handling any chemical 

products, read the manufacturers’ 
product label and the Material Safety 
Data Sheets (MSDS) for important 
health, safety and environmental 
information. Always observe 
manufacturers recommendations 
when handling chemicals. 

To obtain MSDS Sheets for any Neschen-Accutech 
products, contact Neschen-Accutech Technical Services 
at (410) 379-5688 or (800) 490-4232. 

 

 

 

 

 

 

 

 

 

 

 

PREVENTIVE MEASURES 

Do not feed objects such as staples, paper clips and 
rough or abrasive materials through the laminating 
rollers.  

Keep all objects, such as tools, rulers, pens, markers and 
knives away from the roller opening. To prevent such 
items from accidentally being fed into the rollers, do not 
leave them on the laminator. 

 

SAFETY SYMBOLS USED ON THE LAMINATOR 

 

ROTATING PARTS: RISK OF INJURY 

 

 

WARNING:  Failure to use caution near rotating 

rollers could result in physical injury.  
Be careful that items such as loose 
clothing, long hair and jewelry do not 
become entangled in rotating parts. 

 

ELECTRICAL PARTS:  

DANGER OF BEING INJURED 

BY ELECTRICITY 

 

DANGER!   ATTEMPT TO ACCESS THIS AREA 

COULD RESULT IN PHYSICAL 
INJURY BY HIGH VOLTAGE.   

 

ONLY AUTHORIZED MAINTENANCE 
OR SERVICE TECHNICIANS SHOULD 
ATTEMPT REPAIR OF THIS AREA.  

 

 

 

 

 

 

 

 

 

 

 

Содержание ACCU-18XE

























Отзывы: