background image

 

 

 

 

 

 

 

23 

L I M I T E D   W A R R A N T Y

Neschen-Accutech warrants to the original consumer 
purchaser that each new ACCU-18XE Liquid 
Laminator, which proves defective in materials or 
workmanship within the applicable warranty period, will 
be repaired or, at our option, replaced without charge.  

The applicable warranty shall be one year (parts) and 
ninety days (electrical) from date of purchase. 

“Original consumer purchaser” means the person who 
first purchased the product covered by this warranty 
other than for purpose of resale. 

This warranty extends to and is enforceable by only the 
original consumer purchaser, and only for the period 
(during the applicable term), which the product remains 
in the possession of the original consumer purchaser. 
This warranty does not apply if it is found that at any 
time the equipment has not been used for its intended 
purpose. 

This warranty does not cover any accidental damage. 

For more information regarding this warranty, please 
contact your distributor. 

 

WARNING:  Any unauthorized changes or 

modifications to this unit without 
Neschen-Accutech’s prior written 
approval will void the user’s warranty 

and will transfer health and safety 
obligations to the user. 

WARNING:  Changes or modifications to this unit 

not expressly approved by the party 
responsible for compliance could void 
the user's authority to operate the 
equipment 

All rights are reserved. No part of the document may be 
photocopied, reproduced, or translated to another 
language without the prior written consent of Neschen-
Accutech. 

The information contained in this document is subject 
to change without notice and should not be construed 
as a commitment by Neschen-Accutech.  

Neschen-Accutech assumes no responsibility for any 
errors that may appear in this document. Nor does it 
make expressed or implied warranty of any kind with 
regard to this material, including, but not limited to, the 
implied warranties of merchantability and fitness for a 
particular purpose. 

Neschen-Accutech shall not be liable for incidental or 
consequential damages in connection with, or arising 
out of the furnishing, performance, or use of this 
document and the program material, which it describes.  

 

 

Содержание ACCU-18XE

























Отзывы: