background image

11

  AIO Plus 

Default Cycle Step Times 

Minutes

  Step 1 

Air Release (non-adjustable) 

6

  Step 2 

Backwash 

10

  Step 3 

Rest 

5

  Step 4 

Air Replenish 

20

  Step 5 

Rapid Rinse 

5

Starting Extra Regeneration Cycle

1. To Start 

Delayed Extra Cycle:

 

Example: 

[1]

-  If Days Remaining Until Next Regeneration does not read ‘1’, press and hold the 

Set/Change

 button for 3 

seconds until the display reads ‘1

-  Regeneration cycle will initiate at the next designated regeneration time.

2. To start 

Immediate Extra Cycle:

 First complete above step.

-  Press and hold the 

Set/Change

 button.

-  After 3 seconds, the regeneration cycle will begin.

3. To 

Fast Cycle

 through regeneration: First complete above 2 steps.  

Press and hold the 

Set/Change

 button for 3 seconds to advance to the next cycle step. 

 

NOTE: 

Fast Cycle is not necessary unless desired to manually step through each cycle step.  

(Repeat until valve returns to the home display)

Regeneration Cycle

 NOTE: 

Depending upon system pressure and other factors, it is possible to observe flow to drain in the rest cycle.

-When the valve is between positions, the display will flash the number of the step it is moving towards.
-The default time at which regeneration will occur is 12:00 a.m.
The motor’s run direction during a particular regeneration cycle step is indicated by the rotation direction of the  
last 2 digit displays.

Example:

 

5-

AIO Plus Connected Series

  

Programming the Control Valve

Содержание AIO Plus Connected Series





















Отзывы: