11
-
Use the same type of cable (cable with sheath and core in silicone).
-
Prepare the correct cross-section of the cables.
-
To avoid connection errors, use the same coloring of the wires.
For wiring and electrical connections see following diagrams:
Connection of a K-LOCK to a chain actuator
Connection of a K-LOCK to more chain actuators
10. START-UP OPERATIONS
In order to prevent damage, do not apply the 24V
power supply voltage to the
system before having performed the start-up.
Strictly following the work steps below will guarantee a problem-free installation.
10.1. With actuator
The connections between chain actuator and K-LOCK have been made and the
operation has already been bench tested; when opening the K-LOCK opens, goes to
18 or 36 mm (the hook moves towards the outside of the machine) and then the chain
of the actuator comes out. When closing, first the chain of the actuator re-enters
completely and then the K-LOCK goes to 0
(the hook moves towards the center of the
machine towards the power supply cable).
Caution:
First the RESET procedure indicated in the instructions of the INKA
356 actuator should be executed.
Keep the window unhooked from the chain.
If necessary, operate on dip-switch 1 to correct the stroke;
(see Chapter 7. “Setting
the dip-switches”).
Supply power [24V
] and move the hook into the opening stroke-end position (18 or
36), then cut off the power.
Hook up the window, i.e. check that the hook is inserted in the pawl of the sliding
accessory.
ACTUATOR
ACTUATOR
ACTUATOR
24V
24V
Supply power again and check operation of the assembly, which must be as seen on
the bench.
Repeat the complete cycle a second time.
Now if everything works perfectly, check that all the screws are tightened correctly and
the cables are orderly and well
10.2. Without actuator (test)
Ensure that the hook is inserted in the pawl of
Select dip2=OFF and dip1 according to the desired stroke.
Supply the power supply voltage [24V
depending on the power supply orientation on wire 1. The movement must be complete
up to the stroke-end without obstacles.
11. MAINTENANCE OR CLEANING
In order to guarantee problem
after about 1000 opening cycles and at least once a year:
-
Check all the screws to ensure that they are
which must be loosened by ½ turn.
-
Check that the wing is seated perfectly in the frame of the window; if necessary, adjust
the fastening.
-
Check all parts for damage and wear. If necessary, replace the damaged par
12. EMERGENCY OPERATIONS OR MALFUNCTIONS
Strictly follow the instructions provided below.
Observe the safety standards referred to in this booklet.
12.1. Emergency operations
First set dip2 = OFF (free) and power the lock directly, moving the hook to the OPEN stroke
end (18 or 36 mm).
12.2. Malfunctions of the device
Since the user cannot repair a defective lock safely or correctly, this is not allowed. Repairs
may only be carried out in the factory.
warranty becomes null and void; therefore it’s best to replace the device or have it
repaired. If the mechanism is stuck, first check to see if there is a power failure. If problems
arise during installation or operation of the device, it’s advisable to evaluate the following
possible causes of malfunction.
Problem
The device does
not work.
Lack of electricity to the power
supply unit.
The power supply unit does not
supply 24V
12
Supply power again and check operation of the assembly, which must be as seen on
Repeat the complete cycle a second time.
Now if everything works perfectly, check that all the screws are tightened correctly and
the cables are orderly and well-protected.
Without actuator (test)
Ensure that the hook is inserted in the pawl of the sliding accessory and can move.
Select dip2=OFF and dip1 according to the desired stroke.
Supply the power supply voltage [24V
]: check the OPEN or CLOSE movement,
depending on the power supply orientation on wire 1. The movement must be complete
end without obstacles.
MAINTENANCE OR CLEANING
In order to guarantee problem-free operation, the following operations must be carried out
after about 1000 opening cycles and at least once a year:
Check all the screws to ensure that they are tight, except for the two that fix the hook
which must be loosened by ½ turn.
Check that the wing is seated perfectly in the frame of the window; if necessary, adjust
Check all parts for damage and wear. If necessary, replace the damaged par
EMERGENCY OPERATIONS OR MALFUNCTIONS
Strictly follow the instructions provided below.
Observe the safety standards referred to in this booklet.
Emergency operations
First set dip2 = OFF (free) and power the lock directly, moving the hook to the OPEN stroke
Malfunctions of the device
Since the user cannot repair a defective lock safely or correctly, this is not allowed. Repairs
out in the factory. If the device is opened or tampered with, the
warranty becomes null and void; therefore it’s best to replace the device or have it
repaired. If the mechanism is stuck, first check to see if there is a power failure. If problems
ring installation or operation of the device, it’s advisable to evaluate the following
possible causes of malfunction.
Possible cause
Resolution
Lack of electricity to the power
supply unit.
Check the presence of
or the state of the automatic
circuit-breaker or safety switch.
The power supply unit does not
supply 24V
.
Check that the power supply unit
and safety switch are operating
properly.
Supply power again and check operation of the assembly, which must be as seen on
Now if everything works perfectly, check that all the screws are tightened correctly and
the sliding accessory and can move.
]: check the OPEN or CLOSE movement,
depending on the power supply orientation on wire 1. The movement must be complete
free operation, the following operations must be carried out
tight, except for the two that fix the hook
Check that the wing is seated perfectly in the frame of the window; if necessary, adjust
Check all parts for damage and wear. If necessary, replace the damaged parts.
First set dip2 = OFF (free) and power the lock directly, moving the hook to the OPEN stroke-
Since the user cannot repair a defective lock safely or correctly, this is not allowed. Repairs
If the device is opened or tampered with, the
warranty becomes null and void; therefore it’s best to replace the device or have it
repaired. If the mechanism is stuck, first check to see if there is a power failure. If problems
ring installation or operation of the device, it’s advisable to evaluate the following
Resolution
Check the presence of electricity
or the state of the automatic
breaker or safety switch.
Check that the power supply unit
and safety switch are operating
