7
4. GENERAL INFORMATION ABOUT THE ACTUATOR
The actuator of the INKA 356 series moves the window by means of a chain that runs
inside the device. The chain is moved by a gearmotor driven by an electric motor, which
in turn is powered and controlled by an electronic card. The opening and closing
movement is determined by the polarity of the power supply wires depending on how the
wiring is carried out (see wiring diagrams on page 15).
The position of the chain’s stopping point for the closing stroke-end (re-entry of the chain)
is self-determined by power absorption; therefore no adjustments are required for closing.
The actuator leaves the factory with the chain protruding about 1 cm from the re-entry
stroke-end to facilitate its assembly on the window.
The actuator is coupled to the support brackets by means of a (Nekos patented) quick-
connect coupling, without clamping screws, that allows the actuator to rotate in order to
follow the chain’s stroke, even on windows with reduced height.
5. TECHNICAL DATA
Model
INKA356
230V
INKA356
230V
SYNCRO³
INKA356
24V
INKA356
24V
SYNCRO³
Force exerted by thrust and traction (F
N
)
350 N (see force chart)
Strokes (S
V
)
300
(100,200) –
600
(400,500) –
800
(600,700) –
1000
(800,900)
Power supply voltage (U
N
)
110-230V~ 50/60Hz
24V
Rated absorbed current (I
N
)
0,33 A – 0,22 A (230V)
0,950 A
Power absorbed at nominal load (P
N
)
27-29 W
23 W
No load speed
11 / 9,5 mm/s
Duration of no load stroke
Stroke 300 / 600 / 800 / 1000 = 28 / 54 / 72 / 90 s
Electrical insulation
Class II
Class III (Selv)
Type of service (D
R
)
2 cycles
Operating temperature
- 10 + 70 °C
Protection index for electrical devices
IP32
Soft-stop function
Yes
Relax function
Yes
Adjustment of connection to window
frame
Position self-determining
Parallel powering of two or more motors
Yes (max 10)
Synchronised function
No
Yes
(Syncro³)
max 8
No
Yes
(Syncro³)
max 8
Holding nominal force
(it can vary
according to the chosen brackets)
1800 N
Stroke-end at opening
Electronic by dip-switch setting
Stroke-end at closing
At absorption of power
Signalling ‘window open/window closed’
Yes, with specific device to request at order
Type and length of power cable
H05VV-F –
2m
FRR/2
– 2,5 m
S-
FG4GA/2-
2m
S-
FG4GA/2-
2m
Dimensions
34,6x37
L468/624/727/824
34,6x37
L408/564/667/764
Weight
0,9 / 1,4 / 1,8 / 2,2 kg
0,8 / 1,3 / 1,7 / 2,1 kg
The data indicated in these figures is not binding and is subject to variation without notification.
6. CONSTRUCTION AND REGULATORY REFERENCES
INTENDED USE.
The actuator is designed and built to move awning windows,
bottom-hung windows, parallel
and skylights. Its use is
conditioning of rooms (230V~ version), while the 24V
smoke and heat exhaust systems controlled by appropriate control units
other use is strongly discouraged, with the supp
case retaining sole liability.
The actuator is manufactured in accordance with the Directives and following
Regulations listed in the attached Declaration of Incorporation and Conformity
Electrical connections must conform to regulations in force for the design and set
up of electrical equipment.
To ensure efficient separation from the grid, an approved type of bipolar “dead
switch should be used. An omnipolar general power switch wit
of 3 mm between contacts should be installed upstream of the control line.
The actuator is individually packaged in a cardboard container and each pack contains:
110-230V~ 50/60Hz or 24V
Instructions manual.
Installation accessories (if requested).
Brackets are not included in the parcel and have to be requested separately in function of
the applications.
IMPORTANT.
The Syncro³ version of the actuator is packed in a cardboard box with
two units and is shipped already tested. However, the RESET procedure must still be
performed
(see section 12.2)
.
When installing a system that requires the use of several Syncro³ actuators or a K
LOCK electro-lock, a new RESET procedure must be performed
7. ID PLATE AND MARKING
The INKA 356 series actuators have CE marking and comply with the Standards listed in
the Declaration of Conformity. They also come with a Declaration of Incorporation, due to
their classification by the Machinery Directive as “partly completed machin
declarations are included in the final pages of this manual.
The plate data is displayed on an adhesive label placed on the outside of the casing,
which must remain intact and visible.
The main information it displays includes: manufacturer's ad
number, technical characteristics, production date and serial number.
In the event of a complaint, please indicate the serial number (SN) displayed on the label.
An explanation of the symbols used on the label to abbreviate the
characteristics is given in the table in the chapter on “TECHNICAL DATA”
8. ACTUATOR DIMENSIONS
The main overall dimensions of the actuator are given in the table below for bottom
and awning sashes. However, for perfect application on the
request the drawings in order to determine the best solution.
8
CONSTRUCTION AND REGULATORY REFERENCES
The actuator is designed and built to move awning windows,
hung windows, parallel-opening windows, light domes, dormer windows
and skylights. Its use is specifically intended for ventilation and natural air
conditioning of rooms (230V~ version), while the 24V
version is intended for
smoke and heat exhaust systems controlled by appropriate control units
other use is strongly discouraged, with the supplier of the entire system in any
case retaining sole liability.
The actuator is manufactured in accordance with the Directives and following
Regulations listed in the attached Declaration of Incorporation and Conformity
Electrical connections must conform to regulations in force for the design and set
up of electrical equipment.
To ensure efficient separation from the grid, an approved type of bipolar “dead
switch should be used. An omnipolar general power switch wit
of 3 mm between contacts should be installed upstream of the control line.
The actuator is individually packaged in a cardboard container and each pack contains:
V~ 50/60Hz or 24V
electrical actuator.
Installation accessories (if requested).
are not included in the parcel and have to be requested separately in function of
The Syncro³ version of the actuator is packed in a cardboard box with
already tested. However, the RESET procedure must still be
.
When installing a system that requires the use of several Syncro³ actuators or a K
lock, a new RESET procedure must be performed.
ID PLATE AND MARKING DATA
The INKA 356 series actuators have CE marking and comply with the Standards listed in
the Declaration of Conformity. They also come with a Declaration of Incorporation, due to
their classification by the Machinery Directive as “partly completed machin
declarations are included in the final pages of this manual.
The plate data is displayed on an adhesive label placed on the outside of the casing,
which must remain intact and visible.
The main information it displays includes: manufacturer's address, product name
number, technical characteristics, production date and serial number.
In the event of a complaint, please indicate the serial number (SN) displayed on the label.
An explanation of the symbols used on the label to abbreviate the
characteristics is given in the table in the chapter on “TECHNICAL DATA”
ACTUATOR DIMENSIONS
The main overall dimensions of the actuator are given in the table below for bottom
and awning sashes. However, for perfect application on the window, it is advisable to
request the drawings in order to determine the best solution.
CONSTRUCTION AND REGULATORY REFERENCES
The actuator is designed and built to move awning windows,
opening windows, light domes, dormer windows
specifically intended for ventilation and natural air
version is intended for
smoke and heat exhaust systems controlled by appropriate control units; any
lier of the entire system in any
The actuator is manufactured in accordance with the Directives and following
Regulations listed in the attached Declaration of Incorporation and Conformity
.
Electrical connections must conform to regulations in force for the design and set
To ensure efficient separation from the grid, an approved type of bipolar “dead-man”
switch should be used. An omnipolar general power switch with minimum distance
of 3 mm between contacts should be installed upstream of the control line.
The actuator is individually packaged in a cardboard container and each pack contains:
are not included in the parcel and have to be requested separately in function of
The Syncro³ version of the actuator is packed in a cardboard box with
already tested. However, the RESET procedure must still be
When installing a system that requires the use of several Syncro³ actuators or a K-
The INKA 356 series actuators have CE marking and comply with the Standards listed in
the Declaration of Conformity. They also come with a Declaration of Incorporation, due to
their classification by the Machinery Directive as “partly completed machines”. Both
The plate data is displayed on an adhesive label placed on the outside of the casing,
dress, product name - model
number, technical characteristics, production date and serial number.
In the event of a complaint, please indicate the serial number (SN) displayed on the label.
An explanation of the symbols used on the label to abbreviate the technical
characteristics is given in the table in the chapter on “TECHNICAL DATA”.
The main overall dimensions of the actuator are given in the table below for bottom-hung
window, it is advisable to
