NEC Versa 2000 Series Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 82

background image

Recharging the Battery Pack

There are two ways to recharge the battery pack, Quick Charge and Normal Charge.

A Quick Charge is performed when the system is off or in Suspend mode with the AC
adapter connected. A Normal Charge is performed when the AC adapter is connected and
the system is on. When the battery status LED shows an orange light or blinking orange
light, it is time to recharge the battery. .

To recharge the battery, simply attach the AC adapter to the system. Charging the battery
pack with a Quick Charge takes 1.6 hours with power off. Charging the battery pack with a
Normal Charge takes 6 to 9 hours with power on. These time increments assume that there
are no options connected to the Versa 2000.

REPLACING THE BATTERY PACK

To replace the battery pack with a fully charged battery, press the suspend button to
activate Suspend mode. It is not necessary to turn off system power as long as Suspend
mode is activated. The bridge battery maintains data and system status for up to 5 minutes
while in Suspend mode. Use the steps below to install a charged battery pack.

1.

If power is on, push the suspend switch to put the system in Suspend mode. The
bridge battery saves the memory contents and system status.

2.

Remove the battery cover.

3.

Locate the battery release latch on the bottom of the system. Push the release
latch while removing the battery pack from the compartment.

Figure Section 2-5

Battery Release Latch Location

«
...
58
59
60
61
62
...
»

Содержание Versa 2000 Series



















































































Отзывы:

Нет отзывов

Похожие инструкции для Versa 2000 Series

Chromebook PX14E

Бренд: Ctl Страницы: 12

Бренд: Conrad Electronic Страницы: 3

Barbie B-Bright

Бренд: Oregon Scientific Страницы: 16

Бренд: Alienware Страницы: 124

Бренд: Panasonic Страницы: 5

Бренд: Panasonic Страницы: 28

TOUGHBOOK CF-19KHRJXQV

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 28

Toughbook CF-28P3JAZQM

Бренд: Panasonic Страницы: 36

Toughbook CF-27EB6GDAM

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 44

CF-VEB331 Series

Бренд: Panasonic Страницы: 64

Toughbook CF-28 Series

Бренд: Panasonic Страницы: 72

Toughbook CF-19KDRAXCM

Бренд: Panasonic Страницы: 84

Toughbook CF-19CHBAXBM

Бренд: Panasonic Страницы: 84

Toughbook CF-18NHHZXBM

Бренд: Panasonic Страницы: 95

Toughbook CF-28 Series

Бренд: Panasonic Страницы: 204

Бренд: Samsung Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды