NEC Versa 2000 Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 82

background image

Section 2

Setup and Operation

This section provides setup and operation information for the Versa 2000 series system
(including cabling, power-on verification and using Auto Setup).

UNPACKING THE SYSTEM

Find an area away from devices that generate strong magnetic fields (electric motors,
transformers, etc.). Place the shipping carton on a sturdy surface and carefully unpack the
system. The carton contents include the system, AC adapter, AC power cord, battery,
software diskettes, and user documentation.

SETUP

When connecting power and signal cables, do the following.

1.

Make sure that the system is powered off.

The power switch turns the system on or off. Slide the switch right to turn it on,
slide the switch again to turn it off.

2.

Observe connector alignment marks and keys (when present).

3.

Connect the AC adapter cable to the power connector port as shown in Figure
Section 2-4.

4.

Connect the end of the power cord to the AC input connector on the AC adapter.

5.

Connect the other end of the power cord to an AC power source.

NOTE:

If operating the system on DC power,

verify that the system has a charged battery pack
installed. For information on connecting the AC
adapter to recharge the battery pack during or
after use, see “Recharging the Battery Pack” in
the following section.

6.

Ensure that all connections are properly seated and secure.

7.

When removing or replacing cables, grasp and pull gently on the attached
connectors.

«
...
33
34
35
36
37
...
»

Содержание Versa 2000 Series



















































































Отзывы:

Нет отзывов

Похожие инструкции для Versa 2000 Series

Ferrari 1000 Series

Бренд: Acer Страницы: 130

Ferrari 1000 Series

Бренд: Acer Страницы: 141

5570-2052 - Aspire - Pentium Dual Core 1.73...

Бренд: Acer Страницы: 128

Joybook Lite U101 Series

Бренд: BenQ Страницы: 67

Бренд: Forensic Страницы: 10

Бренд: Acer Страницы: 135

TravelMate 7750G

Бренд: Acer Страницы: 2286

Бренд: Clevo Страницы: 84

Бренд: Fujitsu Страницы: 89

Бренд: Fujitsu Страницы: 80

Бренд: Fujitsu Страницы: 108

Бренд: Fujitsu Страницы: 126

Бренд: Fujitsu Страницы: 320

Бренд: Fujitsu Страницы: 67

LIFEBOOK TH4410

Бренд: Fujitsu Страницы: 124

Бренд: Fujitsu Страницы: 121

Бренд: Fujitsu Страницы: 413

Бренд: Fujitsu Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды