NEC Versa 2000 Series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 82

background image

Table Section 2-2 Control and Switch Functions

Control Function

Reset Switch

Resets the system if the NEC Versa does not respond to keyboard input
or VersaGlide movement. Use this control before powering down the
system and restarting it.

Power Switch

Turns the system on when pushed to the right. Turns the system off
when pushed to the right again.

Keyboard Select Switch When on, selects the U.S. keyboard. When off, selects the United

Kingdom, German Keyboard. The switch is located in the memory
compartment on the bottom of the system.

Power Management

Turns Power Management on when pushed to the right. Turns Power
Management off when pushed to the right again.

Suspend/Resume

Slide the switch for Suspend mode, slide again to resume active mode.

Contrast Control

Adjust the dark/light background on the LCD using this switch (on DSTN
models only).

Brightness Control

Move the control upward to increase brightness on the LCD. Lower the
control to decrease brightness on the LCD. A brighter adjustment uses
more battery power. For longer battery life, decrease the brightness.

LEDs

The NEC Versa 2000 uses LEDs to let the user determine system status. The following list
describes LEDs.

Hard Disk — Green when the system is writing data to or retrieving from the system’s hard
disk.

Diskette — Green when the system is writing data to or retrieving from the diskette in the
A drive.

Power Management — Green when power management is in use. No color when power
management is off. Blinking green when the system is in Suspend mode.

«
...
36
37
38
39
40
...
»

Содержание Versa 2000 Series



















































































Отзывы:

Нет отзывов

Похожие инструкции для Versa 2000 Series

Бренд: IBM Страницы: 110

VERSA SX HARD DISK DRIVE

Бренд: NEC Страницы: 6

Бренд: NEC Страницы: 46

Бренд: NEC Страницы: 96

Бренд: Digitus Страницы: 9

Бренд: Alienware Страницы: 111

Бренд: bto Страницы: 308

Бренд: Toshiba Страницы: 10

Chromebook 3110

Бренд: Dell Страницы: 18

Бренд: Samsung Страницы: 34

Бренд: Samsung Страницы: 78

Бренд: Samsung Страницы: 83

Бренд: Samsung Страницы: 128

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды