NEC UNIVERGE SL2100 Скачать руководство пользователя

Страница: 72 / 196

• RTP/RTCP
• UDP
• IPv4
• T.38 (draft-ietf-sipping-realtimefax-02.txt)

4.3 Supported SIP Methods

The following SIP methods are supported with the NEC SL2100 system:

• REGISTER
• INVITE
• BYE
• CANCEL
• ACK
• PRACK
• Response 1xx 2xx, 3xx, 4xx, 5xx, 6xx

The following features are available:

•

Support the 401 response for the Initial Invite

If 401 message is sent for the Initial Invite, with previous software, the system cannot respond to the
message correctly.

•

Support the 401/407 response for the Invite of Session Timer

If 401/407 response is sent for the invite of Session Timer, the system can send the Invite message
with Authentication header.

•

Support the 128 byte size of Nonce max value sent by the 401/407 message

The Nonce maximum size sent by the 401/407 message is expanded to 128 byte. With previous
software, 64 byte size can be received.

4.4 Supported SIP Trunking Options

The options listed below are supported with SIP Trunking.

• 100rel
• Session Timer
• Early Media

4.5 Supported CODEC

SIP Trunking can use the following CODECs.

• G.729. Low bandwidth requirement, and is used on most Wide Area Network links.

- VAD
- VIF size 20ms~30ms

• G.711 – High bandwidth requirement – usually used on Local Area Networks.
• G.722 – This CODEC is useful in fixed network, Voice over IP applications, where the required

bandwidth is typically not prohibitive.

• G.726 – is an ITU-T ADPCM speech coded standard covering the transmission of voice at rates of

16, 24, 32, and 40Kbps.

ECTION

5 SUPPORTED SIP TRUNKING FUNCTIONS

The functions in this section are supported by NEC SL2100 SIP Trunking.

SL2100

ISSUE 1.0

7-4

SIP Trunking

Содержание UNIVERGE SL2100





































































































































































































Результаты поиска

Содержание UNIVERGE SL2100

Отзывы:

Похожие инструкции для UNIVERGE SL2100

Бренды по названию

Популярные бренды

NEC UNIVERGE SL2100, Сетевое руководство

Результаты поиска

Содержание UNIVERGE SL2100

Отзывы:

Похожие инструкции для UNIVERGE SL2100

Бренды по названию

Популярные бренды