193
9. Appendix
Common Problems & Solutions
(
→
“Power/Status/Lamp Indicator” on page
19
2
.)
Problem
Check These Items
Does not turn on
or shut down
• Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control
is on� (
→
pages
13
,
14
)
• Ensure that the lamp cover is installed correctly. (
→
page
149
)
• Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the room
where you are presenting is particularly warm, move the projector to a cooler location�
• Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end of its
life� If so, replace the lamp� After replacing the lamp, reset the lamp hours used� (
→
page
104
)
• The lamp may fail to light. Wait a full minute and then turn on the power again.
• Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600 meters
or higher� Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH
ALTITUDE] can cause the projector to overheat and the projector could shut down� If this happens, wait a couple
minutes and turn on the projector� (
→
page
97
)
If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an image for
some time and then the projector will display the image� Wait for a moment�
Will turn off
• Ensure that the [OFF TIMER] or [AUTO POWER OFF] is off. (
→
page
93
,
100
)
No picture
• Use the COMPUTER1, the COMPUTER2, the VIDEO or the S-VIDEO button on the remote control to select your
source (Computer, Video or S-Video)� (
→
page
16
) If there is still no picture, press the button again�
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. (
→
page
85
)
• Ensure that the lens cover is open. (
→
page
5
)
• Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. (
→
page
104
)
• Enter your registered keyword if the Security function is enabled. (
→
page
30
)
• Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on
the power to the notebook PC�
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before
being powered up�
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver
or power management software�
• See also the
next page
�
Picture suddenly
becomes dark
• Check if the projector is in the Forced ECO mode because of too high ambient temperature. If this is the case,
lower the internal temperature of the projector by selecting [HIGH] for [FAN MODE]� (
→
page
97
)
Color tone or hue is
unusual
• Check if an appropriate color is selected in [WALL COLOR]. If so, select an appropriate option. (
→
page
92
)
• Adjust [HUE] in [PICTURE]. (
→
page
85
)
Image isn’t square to
the screen
• Reposition the projector to improve its angle to the screen. (
→
page
17
)
• Use the Keystone correction function to correct the trapezoid distortion. (
→
page
22
)
Picture is blurred
• Adjust the focus. (
→
page
19
)
• Reposition the projector to improve its angle to the screen. (
→
page
17
)
• Ensure that the distance between the projector and screen is within the adjustment range of the lens.
(
→
page
130
)
• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens�
Flicker appears on
screen
• Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500 feet/1600
meters or lower� Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTI-
TUDE] can cause the lamp to overcool, causing the image to flicker� Switch [FAN MODE] to [AUTO]� (
→
page
97
)
Image is scrolling
vertically, horizontally
or both
• Check the computer’s resolution and frequency. Make sure that the resolution you are trying to display is supported
by the projector� (
→
page
199
)
• Adjust the computer image manually with the Horizontal/Vertical in the [IMAGE OPTIONS]. (
→
page
87
)
Remote control does
not work
• Install new batteries.(
→
page
9
)
• Make sure there are no obstacles between you and the projector.
• Stand within 22 feet (7 m) of the projector. (
→
page
9
)
Indicator is lit or
blinking
• See the POWER/STATUS/LAMP Indicator. (
→
page
192
)
Cross color in RGB
mode
• Press the AUTO ADJ. button on the projector cabinet or the remote control. (
→
page
24
)
• Adjust the computer image manually with [CLOCK]/[PHASE] in [IMAGE OPTIONS] in the menu. (
→
page
86
)
For more information contact your dealer.
