NEC N8100-2189F Скачать руководство пользователя страница 38

Страница: 38 / 133

4. Names and Functions of Parts

Express5800/T110g-E User’s Guide

Chapter 1 General Description

4.5

Status Indicators

This section explains the indication and meanings of the server LEDs.

4.5.1

POWER LED ( )

POWER LED indicates the power ON/OFF status of the server.

The following table lists POWER LED patterns.

POWER LED pattern

Description

On (green)

The server is normally powered on.

On (amber)

The power cord is plugged in and BMC is being initialized.
The server can be powered on after the amber LED is unlit.

Off

The server is off-powered.

Front view

Rear view

POWER LED

DISK Access LED

SPEED LED

Optical disk access LED

STATUS LED

DISK LED

LINK/ACT LED

AC POWER LED

Содержание N8100-2189F






































































































































Результаты поиска

Содержание N8100-2189F

Отзывы:

Похожие инструкции для N8100-2189F

Бренды по названию

Популярные бренды

NEC N8100-2189F, Руководство пользователя

Результаты поиска

Содержание N8100-2189F

Отзывы:

Похожие инструкции для N8100-2189F

Бренды по названию

Популярные бренды