background image

This section introduces you to your new MultiSync MT830 (SVGA)/

MT1030 (XGA) LCD Projector, provides a list of materials that comes

with your projector and describes the features and controls.

Congratulations On Your Purchase Of The MultiSync
MT830/1030 LCD Projector

The MultiSync MT830/1030 is one of the very best LCD projectors

available today. The multiple LCD panels enable you to project

precise images up to 300 inches across (measured diagonally) from

your PC or Macintosh computer (desktop or notebook), VCR, DVD

player, document camera, or even a laser disc player.

You can use the projector on a tabletop or cart, you can permanently

mount it on a ceiling*

1

, or you can use MultiSync MT830/1030 LCD

Projector to project images from behind the screen. The remote

control can be used wirelessly or with a cable, and you can even use

the remote control with the built-in remote mouse receiver to operate

the mouse on your PC or Mac. But best of all, the MultiSync MT830/

1030 is an NEC LCD projector. That means you can depend on years

of reliable performance and crystal-clear presentations!

I N T R O D U C T I O N

1

Features you’ll enjoy:

Simple set up and operation.

Hot air blown from the vents does not bother the audience during

your presentation since the vents are located on the front.

A high-performance 150 watt short arc high pressure lamp that is

guaranteed for 2000 hours of service or six months, whichever comes
first.

A wireless remote control that operates the projector from any

angle.

A laser pointer that' s built into the remote control.

The power zoom control enables you to adjust the image to be

between 20 and 300 inches (measured diagonally).

Keystone correction allows you to correct trapezoidal distortion

so that the image is square.

White balance control allows you to adjust the brightness and

contrast for each RGB color.

You can choose between video modes depending on your source:

"normal" for a typical picture, "natural" for true color reproduc-
tion, and "camera" for use with a document camera or low APL
picture.

The optional MT Viewer kit allows you to start your presentation

even when a PC is not available at the site.

The "image capture" enables you to use the entire picture as a

background image or to create slides (optional MT Viewer re-
quired).

An image can be projected from in front or behind a screen, and

the projector can even be installed on the ceiling.

NEC Technologies' exclusive AccuBlend™ intelligent pixel

blending technology - an extremely accurate image compression
technology - offers a crisp image with SXGA (1280

2

1024)

resolution*

3

. You can select any point on the screen with the

pointer and enlarge the selected area.

Supports most IBM VGA,  SVGA,  XGA*

2

, SXGA(with

AccuBlend)*

3

, Macintosh, or any other RGB signals within a hori-

zontal frequency range of 15.754 to 85 kHz and a vertical frequency
range of 50 to 85 Hz. This includes NTSC, PAL, SECAM and
NTSC4.43 standard video signals.

Note:  Composite video standards are as follows:
NTSC:

U.S. TV standard for video in U.S. and Canada.

PAL:

TV standard used in western Europe.

SECAM:

TV standard used in France and Eastern Europe.

NTSC4.43: TV standard used in Middle East countries.

The remote control can be used with or without a cable, and you

can even use the remote to operate your PC or Macintosh mouse
wirelessly from across the room with the built-in remote mouse
receiver.

You can control your MultiSync MT830/1030 LCD Projector

with a PC.

The contemporary cabinet design is compact, easy to carry, and

complements any office, board room or auditorium.

Eight kinds of pointers are available for your presentation.

*

1

Installing the MultiSync MT830/1030 LCD Projector on the

ceiling must be done by authorized NEC technicians.C o n s u l t
your NEC dealer for more information.

*

2

An XGA image (1024

2

768) is converted into a 800

2

600 crisp

image with NEC technology's AccuBlend.

*

3

An SXGA image (1280

2

1024) is converted into a 1024

2

768

crisp image with NEC technology's AccuBlend.

INTRODUCTION

13

14

Содержание MultiSync MT830+






















































Отзывы: