NEC Express 320Lc Скачать руководство пользователя страница 124

Страница: 124 / 145

Troubleshooting

6-5

<When starting Recovery Console from Windows Server 2003 CD-ROM>

(a) Insert the Windows Server 2003 CD-ROM into the drive.

(b) When the CD is set, reset the system (press

Ctrl

Alt

Delete

) or press the

power switch to power off and on to reboot the NEC Express5800/ft series.

CD-ROM.

IMPORTANT:

Press any key while the message is displayed.

Otherwise the system will be started up from a hard disk and Recovery
Console will not be started.

(d) When the following message appears on the screen, press

quickly.

IMPORTANT:

Unless

keys are pressed, Recovery Console

does not start up. If the screen for selecting HAL as described in 3 does
not appear, reboot the system and start again from activation of Windows
Server 2003 CD-ROM.

3. When you see the screen for selecting HAL, follow the steps below.

(a) Select “Other” (default) and press

Enter

Содержание Express 320Lc


















































































































































Результаты поиска

Содержание Express 320Lc

Отзывы:

NEC Express 320Lc, Руководство пользователя, Страница: 124 / 145

Результаты поиска

Содержание Express 320Lc

Отзывы: