NEC Express 320Lc Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 145

NEC Express 320Lc Скачать руководство пользователя страница 116

5-14

Procedures after Completion of Installation

Setting up PCs on a Network

If you have computers running on Windows Server 2003, Windows XP/2000/NT4.0, Windows
95/98 that communicate with NEC Express5800/ft series using the TCP/IP protocol, make the
following settings on all computers.

1. Copy the following in the NEC EXPRESSBUILDER CD-ROM or ft control software,

UPDATE CD-ROM to any directory.

\STRATUS\LANG\EN\PROG\FTREG.EXE

TIPS:

ft Update CD is for updating ft control software. It may not be attached to the

product. If software included in the NEC EXPRESSBUILDER CD-ROM is latest at
the time of shipment, the ft Update CD is not attached.

2. Start up the command prompt and enter the directory in which the file mentioned above is

copied, and then enter the following command.

FTREG.EXE

This setting is to avoid a timeout caused by non-communication state between the NEC
Express5800/ft series and computers connected by the LAN protocol that may occur immediately
after the NEC Express5800/ft series startup or a CPU module reinstallation (dual processing).

Non-communication time immediately after the NEC Express5800/ft series startup or module
reinstallation in the system where Windows Server 2003 runs is proportional to the size of memory
mounted and how much applications running use memory.

Because minimum non-communication time is momentary regardless of size of the memory
installed, it will not be considered as non-communication. Maximum non-communication time by
the memory size is as follows:

Memory size

Non-communication time

256MB

About 3.1 seconds

512MB

About 6.2 seconds

1GB About

12.3

seconds

2GB About

24.7

seconds

3GB About

36.3

seconds

6GB About

47.0

seconds

This setup program sets the following Windows registry:

Windows XP/Windows NT/Windows 2000/Windows Server 2003:

Registry key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters
Values:   TcpMaxConnectRetransmissions
Type: REG_DWORD
Set value:  5
Values: TcpMaxDataRetransmissions
Type: REG_DWORD
Set value:  8
Values: TcpMaxConnectREsponseRetransmissions

«
...
114
115
116
117
118
...
»

Содержание Express 320Lc


















































































































































Отзывы:

Нет отзывов