background image

2

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

— Consult the dealer or an experienced radio/TV technician for help.

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus as set out in the Radio Interference Regulations of the Canadian Department of
Communications.

LE PRÉSENT APPAREIL NUMÉRIQUE  N’ÉMET PAS DE BRUITS RADIOÉLECTRIQUES
DÉPASSANT LES  LIMITES APPLICABLES AUX APPAREILS NUMÉRIQUES DE CLASSE
B PRESCRITES DANS LE RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE
ÉDICTÉ PAR LE MINISTÈRE DES COMMUNICATIONS DU CANADA.

CAUTION

The user who makes changes or modifications to the unit without the express approval by the
manufacturer will void user authority to operate the equipment.

ACHTUNG

Der  arbeitsplatzbezogene  Geräuschemissionswert  dieses  Gerätes  beträgt  

  70dB (A)  nach

EN 27779/1991.

Notice

Only CD-ROM discs carrying the label below can be used with this CD-ROM reader.

ECDR3001.PM5

99.1.13, 2:36 PM

3

Содержание CDR-3001

















Отзывы: