NEC CDR-3001 Скачать руководство пользователя

Страница: 8 / 16

Part Names and Functions

Front View

Phones Jack
This jack is used to connect a set of headphones. Please use
headphones with a stereo mini-jack plug.

Volume Control
This control is used to adjust the headphone volume.
NOTE: This control has no effect on the audio output from the LINE

OUT connector on the back of the CD-ROM reader.

BUSY Indicator
This indicator lights umber while data is being read.

Tray Panel
This panel prevents dust from entering the CD-ROM reader.
The CD tray will be ejected when the Load/Eject button is pushed.

Emergency Eject Hole
Use to remove the disc from the CD-ROM reader if the electrical eject
is disabled by software or if power failure occurs. (See page 14
“Emergency Eject” for details.)

Load/Eject
This button is pressed to eject or retract the CD tray when the power
is on.

ECDR3001.PM5

99.1.13, 2:36 PM

Содержание CDR-3001

















Результаты поиска

Содержание CDR-3001

Отзывы:

Похожие инструкции для CDR-3001

Бренды по названию

Популярные бренды

NEC CDR-3001, Руководство пользователя

Результаты поиска

Содержание CDR-3001

Отзывы:

Похожие инструкции для CDR-3001

Бренды по названию

Популярные бренды